Wiring Gigabit Combo Ports
JetNet 5428G series includes 24 RJ-45 Fast Ethernet ports. The speed of the
Gigabit Ethernet port supports 10Base-T and 100Base-TX. JetNet 5428G
series equips 4 Gigabit SFP ports combo with Gigabit Ethernet RJ-45 ports.
The speed of the SFP port supports 100MB and 1000MB Full Duplex. The
available Gigabit SFP supports Gigabit Single-mode, Multi-mode,
BIDI/WDM single-mode SFP transceivers.
While the SFP transceiver is plugged, the fiber port has higher priority than
copper port and moved to the fiber mode automatically.
Wiring RS-232 Console Cable
Korenix JetNet 5428G attaches one RS-232 cable in the box. Connect the DB-
9 connector to the COM port of your PC, open terminal tool and set up serial
settings to 9600, N,8,1. (Baud Rate: 9600 / Parity: None / Data Bit: 8 / Stop
Bit: 1) Then you can access CLI interface by console cable.
Note: If you lost the cable, please contact with your sales or follow the pin
assignment to buy a new one.
5 Years Warranty
Each of Korenix’s product is designed, produced, and tested with high
industrial standard. Korenix warrants that the product(s) shall be free from
defects in materials and workmanship for a period of five (5) years from the
date of delivery provided that the product was properly installed and used.
This warranty is voided if defects, malfunctions or failures of the warranted
product are caused by damage resulting from force measure (such as floods,
fire, etc.), other external forces such as power disturbances, over spec power
input, or incorrect cabling; or the warranted product is misused, abused, or
operated, altered and repaired in an unauthorized or improper way.
Attention! To avoid system damage caused by sparks, please DO NOT
plug in power connector when power is on.
The product is in compliance with Directive 2002/95/EC and 2011/65/EU of
the European Parliament and of the Council of 27 January 2003 on the
restriction of the use of certain hazardous substances in electrical and
electronics equipment (RoHS Directives & RoHS 2.0)
Korenix Customer Service
KorenixCARE is Korenix Technology’s global service center, where our
professional staffs are ready to answer your questions at any time.
Email address of Korenix Global Service Center: [email protected]
Support
Korenix JetNet 5428G attaches one RS-232 cable in the box. Connect the DB-
9 connector to the COM port of your PC, open Terminal tool and set up serial
settings to 9600, N,8,1. (Baud Rate: 9600 / Parity: None / Data Bit: 8 / Stop
Bit: 1) Then you can access CLI interface by console cable.
Note:
If you lost the cable, please contact with your sales or follow the pin
assignment to buy a new one.
Preparation for console management
Attach the RS-232 DB9 connector to your PC’s COM port. Connect the RJ-45
based RS-232 connector to the console port of the JetNet 5428G.
1. Go to Start
ۀ
Program
ۀ
Accessories
ۀ
Communication
ۀ
Hyper Terminal
2. Give a name to the new console connection.
3. Choose the COM name, and select the correct serial settings. The serial
settings of the JetNet 5428G are as below:
Baud Rate: 9600 / Parity: None / Data Bit: 8 / Stop Bit: 1
4. After connected, you can see Switch login request. Type the username and
password then you can login. The default username is “admin”, password is
“admin”.
5. Follow the manual to configure the software features.
Preparation for Web management
Before you attempt to use the embedded web interface to manage switch
operation, verify that your JetNet 5428G is properly installed on your network
and that every PC on this network can access the switch via the web browser.
1. Launch the web browser on the PC.
2. Type http://JetNet 5428G_IP_Address (The default IP address is
192.168.10.1.) then press Enter.
3. The login screen will appear next. Key in the user name and the password.
The default user name and password is admin/admin.
4. Click OK, and then the Home page of the web-based management interface
will appear.
5. At the left column of the web management interface is the software function.
The right column lists the available settings. The top column indicates the front
panel and shows the link status of each interface.
Preparation for Telnet management
Go to Start
ۀ
Program
ۀ
Accessories
ۀ
DOS Prompt, Type Telnet 192.168.10.1
(Default IP Address) then press Enter.
Korenix Technology Co., Ltd.
(A Beijer Electronics Group Company)
Tel:+886-2-89111000
Fax:+886-2-29123328
Business service:[email protected]
Customer service:[email protected]
www.korenix.com
CPQ000N5428001
Patent No. (Taiwan):
Granted Invention: I 313547
Granted Invention: I 321415
Granted Invention: I 344766
Granted Invention: I 346480
Granted Invention: I 356616
Granted Invention: I 364684
Granted Invention: I 376118
Granted Invention: I 393317
Granted Invention: I 398066
Granted Invention: I 398125
Granted Invention: I 459757
Utility Model: M 339841
Utility Model: M 339840
Wiring Gigabit Ethernet Ports
JetNet 5428G includes 4 RJ-45 Gigabit Ethernet ports. The Gigabit Ethernet
ports support 100Base-TX and 1000Base-TX, full or half duplex modes. All
the Gigabit Ethernet ports will auto-detect the signal from connected devices
to negotiate the link speed and duplex mode. Auto MDI/MDIX allows users
to connect another switch, hub or workstation without changing straight
through or crossover cables.
Note that crossover cables simply cross-connect the transmit lines at each end
to the received lines at the opposite end.
Wiring Fiber Ports
The SFP ports accept standard Gigabit MINI GBIC SFP transceiver. But, to
ensure system reliability, Korenix recommends using the Korenix certificated
Gigabit SFP Transceiver. The web UI will show unknown vendor type when
choosing the SFP which is not certificated by Korenix. The certificated SFP
transceiver includes 100Base-FX single/multi mode, 100/Gigabit BIDI/WDM,
1000Base-SX/LX single/multi mode ranger from 550m to 80KM.
The way to connect the SFP transceiver is to plug in SFP fiber transceiver fist.
Cross-connect the transmit channel at each end to the receive channel at the
opposite end as illustrated in the figure below. The SPF cage is 2x1 design,
check the direction/angle of the fiber transceiver and fiber cable when inserted.
Note:
This is a Class 1 Laser/LED product. Don’t look into the Laser/LED
Beam.
Device Management
