background image

4

V. Principles of Operation

The main component of the heat exchangers is counterflow aluminum element through
which heat transfer occurs.
Ambient blower draws ambient air from the bottom inlet through an aluminum mesh air
filter, through the element and exhaust it through a discharge grill.
Cabinet blower draws cabinet air from the top inlet through the element and exhaust it
through the bottom discharge into the cabinet.

VI. Specific Model Data

Mounting

Kooltronic Heat Exchangers have been engineered to be installed easily. To avoid damaging
your Heat Exchanger, please read the following information before installation:

1.

See Page 5 for proper orientation.

2.

NOTE: 

Make sure the cutouts don't interfere with components inside your cabinet.

3.

Mount the unit to the outside of the cabinet using all the mounting hardware supplied by
Kooltronic. Secure all screws, but do not to overtighten. 

Blower

Ambient Air

with

Heat Load

Heat

Exchanger

Cooled Air

Cabinet

Blower

Heated Air

Ambient

Air

In an Air-to-Air Heat Exchanger, heat from air surrounding the
components is removed by a specially designed heat transfer
element before being routed back into the enclosure.

Содержание KTHE200









Отзывы: