background image

5

Drawings and Dimensions

(20)

.312 DIA.

HOLES

POWER
CORD

WATER
INLET

WATER
OUTLET

19

36

8

3/

8

17

1/

8

1.50 DIA. POWER

CORD HOLE

if warm air

return does not

extend to this

level.

4

COOL AIR
OUTLET TO
ENCLOSURE

1

3/

4

19

18

1/

4

16

7/

8

13

7/

8

36

22

18

2

1/

2

1

SIGNAL

CIRCUIT

POWER

CORD

WATER

OUTLET

WATER

INLET

51*

19

12

17

3/

16

12

15/

16

HEIGHT

EXTENSION

(location when

used)

(24)

.312 DIA.
HOLES**

19

18

16

13/

16

14

WARM AIR

RETURN FROM

ENCLOSURE

COOL AIR

OUTLET TO

ENCLOSURE

9

1/

2

3

1/

2

1/

2

 TYP.

6

TYP.

3

1

1/

2

5

6 TYP.

51*

WARM AIR

RETURN FROM

ENCLOSURE

KPHE36/39

1/

2

" Copper tubing hook-ups. Inlet: Female; Outlet: Male.

4 Equal Spaces @ 3

1/

2

" = 14”

To use with Height Extension(s), order model KPHE36.  Dimensions of the unit are the same.
Consult KOOLTRONIC for installation location.

Enclosure opening should be located as high as possible within this area,
and equal or exceed size of cool air outlet.


1/

2

1

1/

16

22

15/

16

*

* Add 12” for each
  height extension used.

** Add (4) holes, 2 each side,
    for each 12” height
    extension used.

C

L

3/

8

1

1/

16

Dimensions (inches) are for reference only and are subject to change.

Содержание KPHE36 Series









Отзывы: