background image

Principles of Operation (con’t)

MAX AND MIN TEMPERATURE MEMORIZATION

HOW TO SEE THE MIN TEMPERATURE:

1) Press and release the down arrow       key.

2) The “Lo” message will be displayed followed 

by the minimum temperature recorded.

3) Press the down arrow       key again or wait 5 seconds

to restore normal display.

HOW TO SEE THE MAX TEMPERATURE:

1) Press and release the up       arrow key.

2) The “Hi” message will be displayed followed 

by the maximum temperature recorded.

3) Press the up arrow        key again or wait 5 seconds to

restore normal display.

HOW TO RESET THE MAX AND MIN TEMPERATURE
RECORDED:

1) Press the SET key for more than 3 seconds while the

max or min temperature is displayed. (rSt message 
will be displayed.)

2) To confirm the operation, the “rSt” message starts 

blinking and the normal temperature will be displayed.

MAIN FUNCTIONS

HOW TO SEE THE SETPOINT:

1) Press and immediately release the SET key. 

The display will show the set point value.

2) Press and immediately release the SET key, or 

wait 5 seconds to display the probe value again.

HOW TO CHANGE THE SETPOINT:

NOTE: The standard set point is 80°.  

1) Press the SET key for more than 2 seconds to 

change the set point value.

2) The value of the set point will be displayed and 

the °

or °

LED starts blinking.

3) To change the set value push the up        or down 

arrow        keys within 10 seconds.

4) To store the new set point value push the SET 

key again, or wait 10 seconds. 

HOW TO CHANGE A PARAMETER VALUE:

To change a parameter’s value, operate as follows:

1) Enter the Programming mode by pressing the  

SET plus down arrow keys for 3 seconds (the 
°

or °

LED starts blinking).

8

2) Select the required parameter. Press the SET 

key to display its value. 

3) Use up or down arrow keys to change its value.

4) Press SET to store the new value and move to

the following parameter. To exit, press SET and
the up arrow keys or wait 15 seconds without 
pressing a key.

NOTE: The set value is stored even when the 
procedure is exited by waiting for the time-out 
to expire.

HOW TO LOCK THE KEYBOARD:

1) Press and hold the up and down arrow keys 

simultaneously for more than 3 seconds. 

2) The POF message will be displayed, and the 

keyboard will be locked. At this point, it will only
be possible to see the set point or the MAX or 
MIN temperature stored. 

3) If a key is pressed more than 3 seconds, the 

POF message will be displayed.

HOW TO UNLOCK THE KEYBOARD:

1) Press and hold the up and down arrow keys 

simultaneously for more than 3 seconds until 
the Pon message is displayed. 

OPTIONAL MONITORING SYSTEM

TTL SERIAL LINE - FOR OPTIONAL MONITORING
SYSTEMS:

The optional TTL serial line, available through the
HOT KEY connector, allows through the use of
the external TTL/RS485 converter, connection of
this digital converter to a monitoring system that is
ModBUS-RTU compatible (X-WEB500/3000/300).
Connections are provided through an external 2-
position terminal block.

Содержание K2A6C6HL40LV




















Отзывы: