KBox A-330-RPI - Draft
// 21
5.1.1.
Power Connector
There is one 2-pin power connector on the front panel supporting an input DC voltage range of 9 VDC to
32 VDC, see Figure 4 (pos.1). The mating connector required to connect the power connector to a DC main power
source is not supplied with the KBox A-330-RPI. For information on how to connect the supplied mating connector to
the front panel input power connector, refer to Chapter 9.2.1: Wiring the DC Mating Power Connector.
For the pin assignment of the Input power connector, refer to Chapter 12.2.1: Input Power Connector.
5.1.2.
Protective Earth
The GND pin of the power connector is connected to protective ground of the electronics and also to the metal
housing of the KBox A-330-RPI.
5.1.3.
Micro HDMI
There is one micro HDMI 1.4 interface (1920 x1080 pixel resolution), for video/audio solutions, see Figure 4 (pos.9).
For the pin assignment of the HDMI connector, refer to Chapter 12.2.2: Micro HDMI Connector.
5.1.4.
Ethernet (LAN1, LAN2)
There are two LAN ports both supporting 10/100 Mbit Ethernet, see Figure 4 (pos.3).
For the pin assignment of the RJ45 Ethernet connectors, refer to Chapter 12.2.3: ETH RJ45 Connectors (X600, X700).
5.1.5.
USB 2.0
There are two USB 2.0 ports allowing for the connection of a USB 2.0 compatible devices, see Figure 4 (pos.2).
For the pin assignment of the USB 3.0 connector, refer to Chapter 12.2.4: USB Port.
5.1.6.
USB 2.0 OTG
There is a single USB 2.0 OTG port allowing for the USB client connection to a USB 2.0 compatible master device, see
Figure 4 (pos.7).
For the pin assignment of the USB OTG connector, refer to Chapter 12.2.4: USB Port.
5.1.7.
Serial Ports & CAN
There is a single serial port supporting RS232 RX/TX, see Figure 4 (pos.4).
The RS485 port Figure 4 (pos. 5) contains also the wiring for CAN.
For the pin assignment of the serial port connectors, refer to Chapter 12.2.5: Serial Port Connector
5.1.8.
GPIO Ports
There is a four port GPIO interface available on the front panel of the KBox A-330-RPI, see Figure 4 (pos.6).
The voltage level is 24VDC nominally. It can be used as output (24VDC out – high side drivers) or direct input with
24VDC.
Содержание KBox A-330-RPI
