background image

 

 STARTING THE ENGINE

STARTING THE ENGINE

Before starting the engine, make sure the switch is in the “I” (ON) position (see the pictures below). Turn 

the rotary engine speed dial to MAX. Set the engine switch to the “CHOKE” position. Grasp the starter 

handle and slowly pull it until resistance is felt, then pull it with a rapid movement all the way. Repeat the 

operation until the engine starts. After starting the engine, allow the rope to retract without throwing the 

starter handle. Put the flaps in the “RUN” position.

Recommended fuel: 

Recommended fuel: only unleaded gasoline.
Fuel tank volume:

Fuel tank volume: see specifications table.

Wipe up spilled fuel immediately with a clean, dry, soft 

cloth, as the fuel may harm painted surfaces or plastic 

parts.

IMPORTANT!

  

  CHECKING THE OIL LEVEL

CHECKING THE OIL LEVEL

The log splitter is transported free of motor oil. Do not start the engine until it is filled with sufficient amount 

of motor oil.

1. Unscrew the oil dipstick and wipe it out with a clean cloth.
2. Insert the dipstick without screwing it in.
3. Check the oil level by a mark on the oil dipstick.
4. Add oil if its level is below the mark on the oil dipstick.
5. Screw on the dipstick.
Recommended motor oil: 

Recommended motor oil: SAE 10W30, SAE 10W40.

Recommended motor oil grade: 

Recommended motor oil grade: API Service SG type or higher.

Motor oil quantity: 

Motor oil quantity: see specifications table.

FILL TO HERE

FILL TO HERE

Use only unleaded gasoline. Using leaded gasoline can 

cause serious damage to the inside of the engine.

IMPORTANT!

  

  COMMISSIONING

COMMISSIONING

1. Fill the crankcase with engine oil. The recommended amount of oil for each model is indicated in the 

specification chart.
2. Check oil level with an oil dipstick. It should be between the MIN and MAX marks on the oil dipstick. 
3. Check fuel level.
4. Check the air filter for correct installation.
IN THE FIRST 20 OPERATING HOURS, THE FOLLOWING REQUIREMENTS SHOULD BE MET:

IN THE FIRST 20 OPERATING HOURS, THE FOLLOWING REQUIREMENTS SHOULD BE MET:
1. After the first 20 operating hours, be sure to change the oil. It is better to drain motor oil while the engine 

is still hot after operation to ensure quick and complete oil draining.
2. Check and clean the air filter and spark plug.

Engine switch

OFF

ON

air damper

fuel valve

Open

Closed

Open

Closed

www.ks-power.de/en

   

|

    3

Содержание KS 15TKG 52/35


















Отзывы: