KÖNIG & MEYER
GmbH & Co. KG
Kiesweg 2, 97877 Wertheim, www.k-m.de
26750-022-55 Rev.04 03-80-864-00 4/22
26750 Speaker stand
INTENDED USE
This floor stand enables you to attach speakers and monitors
Thanks to the attractive contemporary look plus the space-saving
design the stand is especially suited for presentations, studio and
home
FEATURES & CAPABILITIES
- Load-bearing capacity 35 kg (see safety instructions: section: C)
- Round, flat cast-iron base (ø 450 mm, 6.8 kg)
- Double secured steel tube combination
- Height adjustable from 930 - 1430 mm
- With cone-shaped mounting aid for 35/36 mm speaker enclosures
SAFETY INSTRUCTIONS
A. GENERAL
A.
- The stand should be visually inspected before and after use.
A.
-
Damaged or incomplete stands should not be used or only used after repair.
A.
- Please ensure that the floor is suitable, i.e. level and stable
A.
- If necessary, remove the load before you change the position of the stand
A.
- Keep unauthorized persons away
A.
- Observe the instruction manual and keep it for future reference
B. MOUNTING INSTRUCTIONS
B.
- Handle the base and tube combination with care and do not drop
B.
-
(risk of crushing, damage to the floor, etc.)
B.
- Make sure that the screw connections are tight (base, tubes, load)
C. LOAD-BEARING CAPACITY
C.
- The max. load capacity of 35 kg applies exclusively to loads which
C.
-
act exactly vertically on the tube combination.
C.
-
This is NOT given…
C.
-
a. …with off-centre loads, i.e. the centre of gravity of the load is not
C.
-
a.
directly above the tube combination,
C.
-
b. …when the stand is at an angle (e.g. when the floor is inclined or
C.
-
b.
if the base tube is screwed loosely) as well as
C.
-
c. …in case of external influences and disturbances (tugging on the
C.
-
c.
stand, shocks from passers-by, wind forces, vibrations, etc.)
C.
-
This creates TILTING hazards which significantly reduce the specified
C.
-
load-bearing capacity of max. 35 kg.
D. EXTENDING/RETRACTING THE LOAD
D.
- This should be always carried out by two competent persons (P1, P2)
D.
-
P1: holds the extension tube together with the load firmly and securely;
D.
-
P2: secures the selected height by engaging the safety hook
4.5
D.
-
P2:
and tightening the clamping screw
4.6
.
E. DISASSEMBLY
E.
- Always lift the load from the stand first - only then start retracting or
E.
-
dismantling the stand.
SET-UP INSTRUCTIONS
1. COMPONENTS
After unpacking, visually check whether all parts are present and
- as far as can be detected - undamaged.
a
Base/floor plate ø 450 mm
b
Tube combination consisting of:
b
b.1
M20 threaded bolt,
b.2
base tube,
b.3
tension clamp,
b
b.4
extension tube,
b.5
mounting aid
c
Instruction manual
2. ASSEMBLY
2.1
Lay out base plate
a
with felt pads facing downwards.
2.2
Screw the threaded bolt
b.1
of the base tube into the
2.2
base plate
a
up to stop.
2.3 NOTE!
2.3
There should be no air gap between the tube and the plate.
2.3
Please check screw connection regularly for tightness and
2.3
retighten if necessary.
USER INSTRUCTIONS / FUNCTIONS
3. CONNECTION LOAD - STAND
In order to attach the load (loudspeaker/monitor), it should be
equipped with…
3.1 …a plug-in socket (ø 35/36 mm) or be upgraded with a
corresponding part.
You may use:
3.2 Mounting adapters (e.g. K&M 195/8, 24281)
3.3 Flange adapters (e.g. K&M 19654, 19656)
1. COMPONENTS
2. ASSEMBLY
3. CONNECTION
3.
LOAD - STAND
Thank you for choosing this product. Please read and follow the instructions carefully.
They inform you about all the important steps concerning assembly and handling.
We recommend you to keep them for future reference.
