KÖNIG & MEYER
GmbH & Co. KG
Kiesweg 2, 97877 Wertheim, www.k-m.de
26734-000-55 Rev.07 03-80-399-00 3/20
26734 Speaker stand
- Attractive stand thanks to its elegant design for tight spaces
- Load bearing weight max. 20 kg*
- Height adjustable stand tube combination (with locking pin and clamp screw)
- Heavy base plate made of steel, comfortable handle, plug opening and
-
4 felt covered feet
- Height 1100-1810 mm; Distance Rod: ø 35 mm, Placement Guide;
-
Base 480 x 480 mm; Weight: 12,85 kg
SAFETY NOTES
Thank you for choosing this product. The instructions provide directions to all of the important setup and
handling steps. We recommend you keep these instructions for future reference.
A. GENERAL
A.
- Load bearing weight: max 20 kg*
A.
- Proper assignment of setup crew (if needed we recommend 2 physically fit technicians)
A.
- IMPORTANT! The base plate is very heavy and improper use can result in risk to
A.
-
individuals and objects
A.
- Wear protective gloves during assembly
A.
- In particular, during assembly do not drop the load - or crush limbs
A.
- Base plate and tube combination must be screwed in as far as it goes
A.
- Careful and attentive handling is required when adjusting the stand - due to the possibility
A.
-
of pinching or wedging your hand
A.
- Moving of the stand, particularly if the speakers are attached, is not permitted (Could fall
A.
-
over, component stress)
A.
- Keep unauthorized personnel away from the stand with speaker
A.
- Only to be used indoors
B. PRIOR TO USE
B.
- The stand should undergo visual inspection prior to and after use, to ensure that
B.
-
all components are there and to the extent visible in working order.
B.
- Damaged stands may either not be used unless they undergo repair
B.
-
by a qualified technician.
B.
- Equipment and aids (e.g. Ladders) are to be inspected to ensure that they
B.
-
are in working order.
B.
- Be sure that the surface will bear the load and is suitable and level.
C. STAND SETUP
C.
- Please consider the information provided in the SETUP INSTRUCTIONS
C.
- The screw connection between the stand tube and base plate must be screwed in as far
C.
-
as it will go
3.a
C.
- The weight tube combination must be centered, un-centered loads can
C.
-
negatively affect the stability of the stand
C.
- Locking pin
16
must be locked into place
C.
- Tighten the clamp screws - without the use of screws.
C.
-
Manual strength is enough, over-tightening can negatively affect the components.
C.
- Never loosen the locking pin
16
and the clamp screw
18
without having someone
C.
-
hold the speakers on the stand
D. DURING OPERATION
D.
Safety during operation is based on:
D.
1. ...FOLLOWING the points listed here under
A - E.
D.
2. ...MASTERING the LATERAL FORCES (DANGER OF THE STAND FALLING OVER).
D.
2.
Lateral forces should be avoided at all costs. They occur in the case:
D.
2.
a. the stand is tilted (uneven surface)
D.
2.
b. the load bearing weight is not centered
D.
2.
c. external shocks such as bumping into the stand, brushing into the stand, wind etc.
D.
2.
NOTE: Maintain safety distance, keep unauthorized persons away;
D.
2.
Should the effectiveness of the measures not be guaranteed,(e.g. through the safety
D.
2.
distance not being kept and not being checked) the installer should implement the
D.
2.
following additional steps, e.g. rigging, anchoring of the base plate to the floor - suitable
D.
2.
extension/expansion/weighting down of the base plate
E. DISASSEMBLY
E.
- Let the speaker retract slowly and in a controlled fashion.
E.
- First remove the speaker - then unscrew the stand tube from the base
SETUP INSTRUCTIONS
1
Base plate with feet are to be placed feet down in the desired position.
2
Screw the clamp screw into clamping bracket
3
Threaded connector -M20 of the tube combination is to be screwed into the base plate
3
as far as it will go.
3.a
Ensure that a space is not left between the tube and the plate
3.a
NOTE: Regularly check and tighten the screws, if needed.
USAGE NOTES / FUNCTION
DIRECTION of the TUBE COMBINATION
- After the tube combination has been screwed in as far as it will go, the operation
-
elements could point in an undesired direction. This can be corrected.
- We recommend that two people are used for this: one person holds the plate and the
-
other person holds the tube
4
The counter nut on the underside of the plate are loosened with an allen wrench
5
The tube is moved back and forth a bit, so that the female threaded bolt can be
5
removed from the plate
6
Now turn the tube in the desired direction and feed the female threaded bolt into the plate
7
Place the counter nut in the proper position and tighten them with the allen wrench
HANDLE
8
The comfortable handle protects your hands and makes transport and installation
8
of the base plate easier and much safer.
FEET
To protect the floor the base plate has four screw-in feet that are covered in felt.
9
Loose feet must be tighten with a socket wrench (SW8 = M5).
CABLE / PLUG OPENING
10
Attractive appearance: The cables are laid underneath the base plate.
11
Technically on the safe side: the opening provides room for all standard plug types
11
and the plastic ring protects the cables against sharp edges.
COMPONENTS
SET UP
INSTRUCTIONS
DIRECTION OF THE TUBE COMBINATION
HANDLE
CABLE / PLUG OPENING
FEET
