24171 Speaker wall mount with sheet
- Practical and flexible for monitors and loudspeakers
- Load bearing weight: max 15 kg.
- Loudspeaker dimensions: 115-250 mm deep, at least 105 mm wide
- Variable adjustments both for angle (-20°) and direction (+/-50°)
- Tray: adjusts to the size of the loudspeakers. Two clamp screws ensure secure hold
SAFETY NOTES
- Check for damage prior to and after use. Damaged mounts may not be used again.
- Not suitable for outdoors or moist rooms.
- Observe the local mounting regulations (they may deviate from the examples presented here).
- Only mount on suitable walls with the corresponding assembly material (not included in the delivery)
-
Examples - see Point
4
,
5
,
6
. Observe the placement instructions provided by the anchor manufacturer.
- Walls that are too weak or have electrical and water conduits are unsuitable. In case of doubt consult a qualified technician.
- Only use trained technicians to assemble the system.
- Ensure that the screws are tight and load-bearing, in particular as regards the setting of the loudspeaker angle.
- Only to be used with suitable loudspeakers and monitors
-
Weight: max 15 kg. Dimensions: Depth 115-250 mm, Width min.100 mm, Form: parallel edges, edge radius max. 5 mm)
- The placement of the loudspeakers requires two physically fit qualified technicians.
-
One person is to hold and secure the loudspeaker, while the other persons adjusts the tray, and clamps the loudspeakers securely into place.
- Careful and attentive handling is required when adjusting the stand - due to the possibility of pinching or wedging your hand.
- External influences such as bumping into the loudspeakers, brushing into the loudspeakers, things thrown at the loudspeaker, wind etc. represent a risk and must be
-
avoided. Measures: Compliance with safety distances, keeping unauthorized persons at a distance, if needed put up safety cordons.
- The instructions provide directions to all of the important setup and handling steps. We recommend, you keep these instructions for future reference.
- In the event of maintenance pay attention to possible risks (wedging, possibility of
-
being knocked into, ladder?)
- To care for the product, use a damp cloth and a non-abrasive cleaning agent.
FAULT-FINDING (F) and REPAIR (R)
F: Mounting parts are not stable
F:
R: Tighten the screws
F: Loudspeaker is not securely fastened to the tray
F:
R: For secure hold, see steps
7
-
18
F:
R: Check loudspeaker, in particular check if the dimensions (Depth 115-250 mm,
F: R:
Width min. 105 mm) as well as the form of the housing
F: R:
(parallel to the wall, edge radius front and back <5 mm) fit
SET UP INSTRUCTIONS
Loudspeaker Mount 24171 comes pre-assembled
and all that needs to be done is:
a. to mount it to the wall: Section 1. & 2.
b. and it must be adjusted to the loudspeaker: Section 3 & 4
1. PREPARE WALL MOUNT
1
Hold the Wall mount plate vertically
2
Mark the drill holes 6x
3
Drill the anchor holes 6x
3
- 6 mm for Bolt Anchors
3
- 8 mm for Frame Anchors
2. MOUNT EXAMPLES
4
Anchor hole
4
prepare 6x
- drill and
-
blow out hole
- Drill hole
- flush
- blow out
- Drive in the
-
anchor
- Drive in the
- frame anchor
- Place Wall
-
mount,
- Tighten nut
-
and washer
- Mount
- wall plate
- Attach with
- screws
5
Insert
5 anchor 6x
6
Attach wall
6 plate securely
CHECK, MAINTENANCE, CLEANING
TECHNICAL DATA / SPECIFICATIONS
A.
Concrete Wall - Example: Bolt-Anchor
A.
M6 x 65 mm
C.
Injection Molding Anchor
C.1
- without sieve bushing for solid masonry and concrete
C.2
- with sieve bushing for hollow bricks / or with anchor threaded rod M6 or female thread M6
Advantages: Mount without expansion, as such the mount can be used as often as needed; mount close to the edge (at least 100 mm distance). Please follow the
assembly/mounting instructions provided with the products.
B.
Perforated bricks - Example: Frame Anchors
B.
8 x 80 mm with wood screws ø6 x 85 mm
Material
Wall plate, swivel joint, tray and
adjustment plate: Steel, powder coating, black
Screws: Steel, galvanized
Caps, cushioning: Plastic (PE, PA)
Load
Loudspeaker up to 15 kg, depth: 115-250 mm, width: min.105 mm
Dimension W x D x H: 200 x 267 x 220 mm, Box: 170 x 510 x 215 mm
Weight
net: 3.18 kg; gross: 3.6 kg
KÖNIG & MEYER
GmbH & Co. KG
Kiesweg 2a, 97877 Wertheim, www.k-m.de
24171-000-55 Rev.1 03-80-813-00 4/18
ø6 (Anchor - Example A)
ø8 (Anchor - Example B)
