SAFETY NOTES
SET UP INSTRUCTIONS
Setting up the 21420 Speaker/Monitor stand is very easy.
It comes pre-assembled and only needs to be set up.
1
Loosen the clamping screw of the triangular
clamp/bracket a bit.
2
Expand the legs until . . .
3
. . . the connecting struts are horizontal.
4
Re-tighten the lower clamping screw.
NOTE:
Manual strength is sufficient; avoid over tightening,
NOTE:
it places undue stress on the components.
FAULT-FINDING (F) and REPAIR (R)
F: Stand is not stable:
F:
R: Ensure that the surface is even.
F:
R: Ensure that the base is expanded to it fully
F: R:
extended position (see
3
= horizontal foot
F: R:
struts) and tighten clamp screw
4
F: The extension tube is loose:
F:
R: Tighten the clamping screw
6
F:
R: Does it weight more than 12 kg?
USAGE NOTES
MOUNT and EXTEND SPEAKER/MONITOR
Do not underestimate the weight of the speaker/monitor
- placement and extension of the loudspeaker/monitor
-
must be carried out by physically fit technicians.
- Firmly grasp the distance rod when adjusting the height to the
-
desired position
5
and and connect the two with the clamp screw
6
.
STAND HEIGHT ADJUSTMENT
5
NOTE: Prior to loosening the clamp screw
5
NOTE:
always hold the extension tube
6
Loosen the clamping screw of the clamp/bracket
7
Adjust the extension tube to the desired height and
7
tighten the clamping screw
6
When retracting the distance rod the reverse order applies.
TECHNICAL DATA
Thank you for choosing this product. The instructions provide directions to all of the important set
up and handling steps. We recommend you keep these instructions for future reference.
KÖNIG & MEYER
GmbH & Co. KG
Kiesweg 2, 97877 Wertheim, www.k-m.de
21420-000-55 Rev.01 03-80-253-00 7/15
- Maximum centric load 12 kg
- Check for damage to the stand prior to and after use,
-
damaged stands may not be used
- Weight distribution must not allow the stand to list to one side
- The floor must be load bearing and even
- Keep unauthorized personnel away from the stand.
-
Protect against risk of tripping or the stand falling over
- Maintain safety when installing the system:
- Tighten screws - but not too tight.
- The maximum stability is given when the base struts of
-
the stand are level
- Be careful when retracting the extension tube the clamp
-
screws of the locking bracket and locking ring, so that
-
the tube glides downward in a slow and deliberate
-
manner and does not snap
- Careful and attentive handling is required when adjusting the
-
stand due to the possibility of pinching or wedging your hand
21420 Speaker/Monitor stand
- for loudspeakers / monitors up to 12 kg
- Equally suited for home, object and public areas
- Light, collapsible aluminum stand, particularly suited for mobile use
- Height: 1290 - 2130 mm, root circle ø 1280 mm, Tube ø 25 mm, Weight: 1.4 kg
Material
Tubes, Threaded Bolts: Aluminum
Brackets: Polyamid (PA)
End Caps: TPE
Connection parts: Steel galvanized
Dimen-
sions
Root circle ø 1280 mm
Height: 1290 - 2130 mm
Extension tube: ø 25 mm
load
max. 12 kg (centric)
Packaging, kg 100 x 90 x 1135 mm, 1.4 kg
Box, kg
130 x 120 x 1185 mm, 1.6 kg
Accessories
(optional)
Carry Case 21422
Flange Adapter ø25 mm
K&M 19665
