background image

KÖNIG & MEYER

GmbH & Co. KG 

Kiesweg 2, 97877 Wertheim, www.k-m.de
19799-000-55  Rev.09  03-80-090-00  1/18

TECHNISCHE DATEN

Material

Holder, joint: Polyamid PA-6
Screws: Steel, galvanized

max. load

Tablets Height: min. 163 mm, max. 242 mm

Tablets

Width: min.102 mm, max. 189 mm

Tablets

Depth: min. 5 mm, max. 11 mm

Packagin

W x D x H: 232 x 55 x 154 mm

Weight

0.21 kg

USAGE NOTES and 
FUNCTIONS (14-21)

FAULT-FINDING (F) and REPAIR (R)

F: Holder is unstable       

F:

B: Check the wall screws

F:

B: Check the connection between the wall plate and holder plate (

3

-

5

)

F: Tablet is not securely in place    

F:

B: Correct the position of the side support ams, so that the corner supports 

F: B:

are properly set on the Tablet without any play (

7

-

9

)

F:

B: Ensure that the lower support arms setting are symmetrical (

8

,

9

F: B:

Asymmetric  support arm settings looks bad and does not ensure that 

F: B:

the Tablet is securely in place.

F:

B: Do not only place the Tablet on the upper support arm, but be sure it 

F: B:

clicks into place (

11

,

12

,

20

).

F:

B: Observe the minimum i.e maximum dimensions (

14

)

FIRST TIME PLACEMENT of the Tablet (6-13)

DIMENSIONS (14)

REMOVING the Tablet (15-17)

REPEATED PLACEMENT of the Tablet (18-20) + (13.a.b.c)

Final Position
- landscape
- clicked into place

Final Position
- portrait
- clicked into place

Twist (Interim Position):
- In between landscape and portrait
- not clicked into place, however 

-

it does stay in the selected position

DIMENSIONS (14)

If the tablet’s dimensions are too large or too
small (atypical) for the mount it will not fit.

REMOVING the Tablet (15-17)
15

Loosen the knurled pins a bit

16

Hold the tablet and LIFT UP 

16

the catch

17

Flip out the Tablet and REMOVE

If you always use the same Tablet PC 
we recommend leaving the support 
arm settings in this set position.

REPEATED PLACEMENT of the 
Tablet (18-20)

for previously set support arms

18

Place the tablet in the lower corner 

18

supports

19

Place the tablet into the upper catch and 

19

gently press until it clicks into place

20

Tighten the knurled pins until the tablet 

20

is gently pressed into place

Check to ensure that the Tablet PC is secure

13.a.b.c

.

FORMAT (21)

The mount and the Tablet can be turned 90°.
Do accomplish this the Tablet does not need to
be removed from the holder.

21

Take the holder and turn it to the 

21

landscape, portrait,

21

- or tilted position!

21

NOTE:  

21

Invisible stops on the holder limit how 

21

far the holder can be turned.

SETUP (6-13)

12

Gently clamp the tablet in the corner 

12

supports by tightening the knurled pins

13

Your Tablet should be securely positioned.

13

Please check that the following 

13

is the case: 

13

a. Is the Tablet securely mounted?

13

b. Are the three knurled handles 

13

b.

properly tightened?

13

c. Are the three plastic finger screws 

13

c.

properly tightened?

If not please take corrective action (

6-11

).

FORMAT (21)

Содержание 19799







Отзывы: