KÖNIG & MEYER
GmbH & Co. KG
Kiesweg 2, 97877 Wertheim, www.k-m.de
19772-300-55 Rev.07 03-80-114-00 6/13
TECHNICAL DATA / SPECIFICATIONS
USER NOTES
SETUP INSTRUCTIONS
19772 iPad Stand
- Long-lived and stable! Your iPad is wonderfully presented.
- Equally suitable for stage, home and studio.
- The iPad is simply attached to the specially adjusted adapter plate.
- The inclination angle can be adjusted smoothly by ergonomic clamp screws.
- Very practical: the handle can be used to present the iPad horizontally or vertically.
- Smoothly adjustable from 700 - 1550 mm.
SAFETY NOTES
Thank you for choosing this product. This instruction manual informs you about the important steps to set up and handle the product.
We recommend to keep the manual in a separate place for a possible later use.
FAULT FINDING (FF) and REPAIR (R)
FF: Holder wobbles
FF:
R: Check screw connection to stand, attach again if required
s.4-6
FF:
R: Tighten wing nut
7
firmly
FF: SEAT of the iPad in the holder
FF:
R: Insert iPad correctly
8
and let it latch audibly
9
FF:
R: Align iPad correctly
14.a
,
14.b
FF:
R: Gently bend the adapter plate into position
15
FF:
R: ATTENTION! Not suitable for iPad 1st Gen. Check iPad.
The iPad-holder can be adjusted in form and inclination.
The iPad does not have to be removed from the adapter plate.
INCLINATION
The iPad can be fastened in any position between the vertical
and horizontal end positions.
10
Hold iPad and loosen the wing nut
11
Tilt iPad as desired and
12
tighten the wing nut again
FORMAT
The holder has a 90°-twist function.
This permits vertical or horizontal presentation of the iPad.
13
Take the adapter plate and turn it horizontally or
13
vertically – or diagonally!
13
Stops in the holder limit the turning range.
ADVICE
Insert the iPad with the activation button
14.a
- at the bottom or
14.b
- at the right.
Side effects: the "tensile forces" the cable causes
during headphone operation cannot twist the holder
because they act against the stop
1
Fold feet apart
2
Loosen base screw and move base down to the stop;
2
tighten base screw again
3
Loosen clamps, adjust extensions to the desired height
3
and tighten clamps again
4
Tighten knurled screw to the stop
5
Screw iPad holder to the threaded pin
6
Clamp knurled screw to the holder
7
Tighten wing nut
8
First insert iPad and then
9
attach it.
Material
Pipes, screws: Steel, black powder-coated, zinc-plated
Clamps: zinc, black powder-coated
Base, joints, clamps, grip, adapter plate: PA-6
Parquet protection: TPE
Load capacity iPad 2nd, 3rd or 4th Generation
Dimensions
Holder: 252,1 x 104,8 x 195,4 mm
Stand: ø 565 x 700/1550 mm
Weight
net: 2,1 kg, gross: 2,7 kg
INCLINATION
FORMAT
ADVICE
SEAT
connection for headphones
connection for
headphones
Home-Button
bottom
if the iPad is
too loose
attach the iPad again,
test it and bend it again
if required
remove iPad and bend
the holder gently but
firmly inside
Home-
Button
right
a. Load:
- Suitable for
2nd, 3rd or 4th Gen.
, not suitable for iPad 1st Gen.
- Carefully attach iPad to the adapter plate and check for
-
secure fit.
- Handle the holder with care, in particular when changing
-
settings (inclination, format).
b. Bottom: - Must be slanted, i.e. level underground with carrying
-
capacity is a requirement
c. Installation: Always hand-tighten clamp screws.
d. Outer influences: Protection from wind, rain, impact, etc.
