KÖNIG & MEYER
GmbH & Co. KG
Kiesweg 2, 97877 Wertheim, www.k-m.de
19724-000-55 Rev.07 03-80-094-00 4/17
TECHNICAL DATA
Material
Swivel Bearing: Polyamid PA-6
Holding Plate: PP
Screws, nuts, washers, springs: steel galvanized
Clamp: aluminum profile
Max. load
iPad Air or iPad (2017)
Dimensions
Holder: 249 x 178,7 mm / Tube ø 11-30 mm
Box: 300 x 102 x 230 mm
Weight
net 0.65 kg, gross 0.95 kg
USAGE NOTES
SET UP INSTRUCTIONS
19724 iPad Air holder
- The connector holds an iPad Air / iPad (2017) securely and comfortably
- At the same time it is suitable for the stage, home and studio
- It is secured with a large clamp to tubes up to ø 30 mm
- Easy to clip the iPad onto the specially adapted
-
holding plate
- Provides any number of adjustments - just the way
-
you want it:
Position, Direction, Vertical/Horizontal
SAFETY NOTES
Thank you for choosing this product.
The instructions provide directions to all of the important set
up and handling steps. We recommend you keep these
instructions for future reference.
FAULT FINDING (F) & REPAIR (R)
F: Holder is unstable
F:
R: Check screws, if needed tighten screws
F: iPad is not firmly in place
F:
R: Place the iPad into the holder correctly (so you can hear the click)
F:
R: ATTENTION! Suitable only for iPad Air or iPad (2017).
F: B:
Not for other iPad Generations.
The iPad Air holder can be adjusted according to the
position and format. The iPad does
not have to be removed from the holding plate
to make the adjustments.
POSITION
The iPad can be placed in any vertical / horizontal position,
the final position can be set. To do this:
1
8
Hold the iPad and loosen the wing nut somewhat
1
9
Pick the position (vertical / horizontal) and
10
re-tighten the wing nut
ORIENTATION
11
a. Loosen the finger screws, and turn the iPad holder,
11
a.
re-tighten the finger screws.
12
b. Hold on to the holder, loosen the clamp screw, place the
12
b.
holding arm in the desired direction , re-tighten the clamp screw.
FORMAT
The holder is equipped with a 90°-turning function (vertical/horizontal)
13
Take the holding plate and place it in the corresponding position
- Hitches within the mount limit how far the holder can be turned.
- In addition, the holding plate clicks into place.
ASSEMBLY
1
The holder consists of two component groups:
1
a. Holding arm with a clamp,
1
b. iPad Air holding plate with a joint-connection.
1
Both parts are connected using wing screws.
2
The clamp is placed around the tube and
2
affixed with a screw
12
PLACEMENT of the iPAD
3
Place the iPad according to the HOME-Button-Symbol
3
Orientation (consult the embossing on the holding plate).
4
First PLACE the iPad into the bottom area and then...
5
... CLIP it into the top.
REMOVAL of the iPAD
6
Hold the iPad and lift the upper hook and
7
remove the iPad
a. Load: - Suitable for iPad Air / iPad (2017).
- Carefully attach iPad to the adapter
-
plateand check for secure fit.
- Handle the holder with care, in particular
-
when changing settings (inclination,
-
format).
b. Stand: - Usually a sturdy K&M-mic/music stand,
- w/suitable tube diameter (ø 11 - ø 30 mm)
- level underground with carrying capacity
-
is a requirement.
c. Installation: - Always hand-tighten clamp screws.
d. Influences: - Protection from wind, rain, impact, etc.
MONTAGE
POSITION & ORIENTATION
FORMAT
PLACEMENT & REMOVAL of the iPAD
Volume Control
Camera (Back)
Camera (Front)
Speakers
Lightning connector
On / Off
Switch
Microphone
3.5 mm-
Connector
bottom
PLACE
Final Position
- horizontal
- as far as it goes
Incline Position:
- tilted (0-90°)
- select any position (Secure position
-
by tightening the wing nut
Final Position
- vertical
- as far as it goes
Final Position
- landscape
- click into place
Incline Position:
- tilted
- cannot be clicked into place, however
-
it does stay in the selected position
Final Position
- portrait
- click into place
Lift up
the hook
Remove
Home-Button
(the holder is embossed with information on where the iPad mini is to be placed)
(false placement results in the embossed user elements being covered up! Please note)
top
CLIP ON
