TECHNICAL DATA
Material
Support arm, support tray, clamp: Steel, powder-coated
Screws, washers, nuts: Steel, galvanized
Caps, handles, spacer, cup: PA-6, PLA
Insert: Foam, black
Load capacity
small devices, percussion accessories up to max. 5 kg
lower load when unsafe stand
Dimensions
Tray internal: 330 x 252 x 20 mm
Foam insert: 329 x 251 x 3 mm
Clamp: for tubes ø 25-42 mm
Can holder: ø 70 x 4 7mm
Weight
2 kg
Packaging
Inside: 465 x 325 x 87 mm, 0.4 kg
ASSEMBLY INSTRUCTIONS
USER REFERENCES
6. DIRECTION - TURN TRAY
6.1
Loosen the wing nut,
6.2
push the tray away from the stand tube if necessary
6.3
Turn the tray,
6.4
push the tray back in direction stand
6.5
Tighten the wing nut again
7. FOAM INSERT
7.1
The foam insert is not glued and can be removed at will.
7.2
Please note the position of the cut-out for the can/cup holder,
7.2
when fitting the foam insert.
7.3
6 Double sided adhesive dots ø 15 mm are included to glue
7.3
the insert into the plate if required.
8. RECESS FOR WIRING
8.1
The clearance in the tray serves...
8.2
...as cable bushing and
8.3
...to lift the foam insert from below
9. CAN/CUP HOLDER
9.1
In addition to cans and cups, the holder can also be used for storing small parts.
9.2
the holder is clipped onto the tray. If required It can be removed and afterwards
9.2
pressed in again. Pay attention to the >clack<-noise.
10. OVERVIEW OF SUITABLE K&M-STANDS
10.1
Stands must have APPROPRIATE TUBES: ø 25-42 mm
10.1
These include:
10.1
- Music stands: 11870,11888, 11889, 11899, 11940, 11960, 11965, 12330, 12331
10.1
- Microphone stands: 20800, 20811, 21411, 21430
10.1
- Monitor stands: 26720, 26740, 26754
10.1
- Speaker stands: 19500, 213, 21302, 21420, 21435, 21436, 21449, 21450,
10.1
- Speaker stands:
21455, 21460, 21463, 21467, 26734, 26735, 26737, 26750
10.1
- Lighting stands: 24610, 24620, 24624, 24625, 24630, 24640, 24645
MAINTENANCE
- Careful handling preserves the function, the load capacity and longevity of the support
- Periodic operation of moving parts preserves their mobility
- Maintenance work may only be carried out in an unloaded condition.
- Damaged parts must not be used again and should be replaced or repaired
- Dirt, moisture and corrosion must be removed
- For cleaning and maintenance use a slightly damp cloth and a non-abrasive
-
cleaning agent
11. STABILITY OF THE INSTALLATION
11.1
The installation (= combination of base, stand, tray and load) must have
11.1
SUFFICIENT STABILITY. Influencing factors are:
11.1
a. Surface: must be load-bearing and level; sloping floors are a danger
11.1
b. Stand: the higher the dead weight and the larger the base circle the better
11.1
c. Support tray - c.1 Tray: place as close as possible to the central support tube
11.1
c. Support tray
- c.2 Clamp: fix rather deep-seated onto the stand
11.1
c. Support tray
- c.3 Support arm: position above but not between
11.1
c. Support tray
- c.3
one of the three legs
11.1
d. Load: max. 5 kg; may have to be reduced if the installation is in danger of tilting
11.2
In case of doubt, we recommend a 5° tilt test.
11.2
TEST CONDITIONS
11.2
The selected installation must not tip over on a plane inclined by 5°.
11.2
WARNING!
11.2
Safety must be ensured when carrying out this test
11.2
(timely picking up of the stand, barriers, safety ropes, etc.).
11.2
Consult qualified personnel if necessary.
11.2
NOTICE
11.2
The 5° tilt test indicates how well the installation can withstand lateral forces.
11.2
Passing the test does NOT imply that the installation is allowed to operate on
11.2
an inclined flooring of up to 5°. In fact, only level flooring/surfaces are allowed.
11.3
MEASURES to be taken if the 5° tilt test is not passed are described under
11.3
11.1.a-d.
Basically, the stand should not run the risk of overturning, even with
11.3
an unfavourable adjustment of the support tray 12227
3. / 4. / 5. / 6. SETTINGS
FAULT-FINDING (F) and REPAIR (R)
F: Installation wobbles R: Check if all components are correctly arranged and the
F: Installation wobbles R:
threads are firmly tightened.
F: Installation wobbles
R: Check stands for stability
F: Can/cup holder is loose R: Press the component into the hole of the tray
F: Tray doesn’t rotated through 360° R: Pull out the tray
6.2
, then turn and push it in
F: Tray doesn’t rotated through 360° R:
again
6.4
and secure.
KÖNIG & MEYER
GmbH & Co. KG
Kiesweg 2, 97877 Wertheim, www.k-m.de
12227-000-55 Rev.05 03-79-117-00 2/20
suboptimal:
- far out
- particularly
-
high
- between
-
two feet
Example:
Speaker stand
214/6
ø 1320 mm
4.4 kg
Support plate
close to the stand
attached
slightly lower
above one
feet
theoretical
tilting lines
Example:
Orchestra music stand
11960
ø 750 mm
3.7 kg
CAUTION:
- far out
- particularly
-
high
- between
-
two feet
- near the
-
tilting line
