CHECK, MAINTENANCE, CLEANING
- In the event of maintenance pay attention to possible risks (e.g. damaged edges?)
- To care for the product use a damp cloth and a non-abrasive cleaning agent.
FAULT-FINDING (F) and REPAIR (R)
TECHNICAL DATA
F: The storage box is difficult to hang into place
F:
R: Check to see if the upper hanging clip i.e. the sides are bent inwards
F: The storage box rattles on the wagon handle tube
F:
R: Check to see if the hanging clip i.e. the sides are bent outwards
F:
R: Replace the lost rubber pad i.e. incorrectly placed pads are to be glued to the proper spot
11936 Storage box for wagon
- The practical addition to the wagon per se
- Suited for storage and transport of music desk accessories
-
Lamps, music sheets, pens, pencils, holders etc.
- Simple installation and handling
- Storage area: W x D x H: 420 x 172 x 135 mm
- Weight bearing load: up to 8 kg
SAFETY NOTES
USAGE INSTRUCTIONS
Material
Box: Steel, powder coating, black
Edge protection: rubber, metal strip
Rubber pad: PUR, black
Load
up to 8 kg
Dimensions
W x D x H
External: 430 x 207 x 236 mm
Internal: 420 x 172 x 133 mm
Weight
3 kg
Box
565 x 230 x150 mm
WEIGHT BEARING LOAD of the storage box
- The maximum weight bearing load is 8 kg.
- The load should be equally distributed.
- Please do not underestimate the load.
- Physical and technical skills are required
- In particular the hanging and removal of the storage box, but also driving
-
the wagon with the storage box attached, particularly if the box is loaded,
-
requires the careful and concentrated focus of all involved.
COMPONENTS
Storage Box 11936 comes completely pre-assembled and consists of:
1
the actual storage box (Steel, black powdered)
2
two edge guard profiles and the side handles
2
(Hand protection, Carrying comfort)
3
two rubber pads are placed on the points where the storage box leans on
3
the wagon's handle tubes (protects the surface, avoids noise)
Prior to use we recommend that a visual inspection is performed on the
product (Completeness and Condition).
HOW TO USE?
4
The storage box is designed in such a manner that it is hung on the
4
"inside" - even in the case of a fully loaded wagon.
4
Advantages: Compact and excellent weight distribution.
5
Unusual - but not impossible - is the hanging of the storage box on the
5
"outside". This increases the space requirements of the wagon and shifts
5
the center of gravity. For this reason, we recommend that the box be hung
5
on the "inside".
HANGING the storage box
1
6
Hold the storage box using both side handles so that the hanging
16
clips face you.
1
7
The hanging clips are centered on the cross tube of the wagon...
1
8
...and the storage box is slowly put in place...
1
9
...until both side pieces are next the tubes on the outside.
19
This ensures that the box does not slip laterally.
10
Be sure that the rubber pads
3
are actually placed between the back
10
wall of the storage box and the tubes. If this is not the case, take
10
corrective action and position the rubber pads properly.
Thank you for choosing this product. The instructions provide directions and the important
setup and handling steps. We recommend you keep these instructions for future reference.
KÖNIG & MEYER
GmbH & Co. KG
Kiesweg 2, 97877 Wertheim, www.k-m.de
11936-000-55 Rev.01 03-80-674-00 8/16
- The storage box is specifically designed for the dimensions of the K&M-Transport Wagon 11935;
- Other uses of this product are subject to the responsibility of the user
- Complying with the security note for Wagon 11935 is the prerequisite for the safe and secure
-
use of Storage Box 11936
- Damage such as e.g. sharp edges or deformed steel can represent a risk; in this case, the
-
product may no longer be used - or it may only be used after it has been repaired
-
by a qualified technician
- Prior to use please check if the storage box has been properly placed: refer to (
6
-
10
).
DIMENSIONS
HANGING THE BOX
HOW TO USE?
COMPONENTS
View
from above
