Konica Minolta SRX-101A Скачать руководство пользователя страница 30

Страница: 30 / 31

28 OPERATION MANUAL

SPECIFICATIONS

Model name

: SRX-101A

Film transport method

: Continuous roller transport.

Film type and sizes

: Sheet film, 10 x 10 cm~ 14 x 17 inch(35 x 43 cm) sizes.

Processing capacity

Process cycle switching

: Available by a service engineer.

Processing solution volumes

: DEV tank

: 1.03 gallons

FIX tank

: 0.47 gallons

WASH tank : 0.37 gallons

Temperature control

: Processing solution temperature;

Controlled by the temperature control tank, with the thermistor monitoring,
and with the heater heating.
Drying temperature;
Controlled automatically according to a fixed temperature setting.

Replenishing system

: Replenishing volume for the film sheet is calculated exchanging with

10"x12" film.

Circulation system

: Continuous pumping of developer and fixer solutions.

Wash water

: Ordinary tap water 41 ~ 86

Water pressure 49 ~ 686 kPa(0.5 ~ 7kgf/cm

, 7 ~ 98psi)

Water supply

: 0.22 gallons(0.8 liters)/min.

Standby functions

: 10min./30min./Continuous operation. (Selectable by a service engineer)

Power source

: AC 115/120V, single phase, 12A, 60 Hz.

Dimensions(W x D x H)

: 24.0 x 26.8(35.4 incl. feed table) x 17.8 inch.

Weight

: 40kg (47kg with processing tank full)

88 lb (104 lb with processing tank full)

Certification

: Conforms to UL, FDA.

Applied standard

: FCC

Heat generation

: Approx.3135kJ/hr max.

Noise level

: Approx.55dB(A) max.

Operating condition

: 59 ~ 86

, 30 ~ 75%RH(no condensation)

Storage and transport condition

: --4 ~ 140

, 20 ~ 95%RH(no condensation)

Accessories

: Measuring cup, Funnel, Installation parts kit, Replacement parts kit,

Replenisher tanks, and Operation manual.

Optional equipment

: Light shield panel, Stand, Splash guard.

*The above specifications are subject to change without prior notice.

Size

Cycle

10 x 12 inch

14 x 17 inch

90sec.

120sec.

180sec.

(sheets/hr)

Содержание SRX-101A
































Результаты поиска

Содержание SRX-101A

Отзывы:

Похожие инструкции для SRX-101A

Бренды по названию

Популярные бренды

Konica Minolta SRX-101A, Руководство по эксплуатации

Результаты поиска

Содержание SRX-101A

Отзывы:

Похожие инструкции для SRX-101A

Бренды по названию

Популярные бренды