Konica Minolta DF-704 Скачать руководство пользователя страница 1

E-1

DF-704 

Dual Scan Document Feeder

INSTALLATION MANUAL

A87R-9550-00

Applied Machines: C368/C308

COLOR MFP: 36 ppm/30 ppm

Product Code: A7PU/A7PY

Caution:

Lifting the machine in an awkward position or 
transporting it in a poorly balanced position could 
result in personal injury. When transporting the 
machine, assign an adequate number of persons 
to the job and ensure that each person can take a 
good position of not being excessively loaded. 
(mass: approx. 12 kg (26-7/16 lb))

1. Accessory parts

Note:

This manual provides the illustrations of the acces-
sory parts and machine that may be slightly differ-
ent in shape from yours. In that case, instead of 
the illustrations, use the appearance of your 
machine to follow the installation procedure. This 
does not cause any significant change or problem 
with the procedure.

2. Installation procedures

(1) Turn OFF the power switch and unplug the 

power cord from the power outlet.

(2) Hold the dual scan document feeder as shown in 

the illustration and remove it from the carton.

Note:

To prevent breakage, do not hold the dual scan 
document feeder by the four corners.

No.

Name

Shape

Q’ty

1. Dual scan 

board

1

2. Hinge cover 

(large)

1

3. Hinge cover 

(small)

1

4. Shoulder

screw A

2

5. Shoulder

screw B

2

6. Mounting 

screw

2

7. Chart

1

8. Installation

manual

1 set

Keep this bag away from babies and 
children. Do not use in cribs, beds, 
carriages, or playpens.

The thin film may cling to nose and 
mouth and prevent breathing. This bag is 
not a toy.

Содержание DF-704













Отзывы: