Konica Minolta CM-3700A Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 42

background image

31

TROUBLESHOOTING GUIDE

If a problem occurs with the Spectrophotometer, please check the following points before
requesting service. If the problem continues to occur even after the suggested corrective
actions have been taken, contact the nearest Konica Minolta-authorized service facility.

Condition

Checkpoint

Recommended action

Refer

to page

Reflectance measurement
results seem strange.

Was specimen
positioned correctly?

Open measurement port
baseplate and check
measurement point.

Are the white calibration
data correct?

Set the correct white
calibration data.

Was white calibration
performed correctly?

Attach White Calibration
Plate correctly and perform
white calibration correctly.

Was zero calibration
performed correctly?

Attach Zero Calibration
Plate correctly and perform
zero calibration correctly.

Is there any obstacle in the
transmittance chamber?

Make sure that there is nothing
in the transmittance chamber.

Was measurement mode
set to reflectance?

By referring to the operation
manual of the software, perform
the operation correctly.

—

Transmittance
measurement results
seem strange.

Was specimen
positioned correctly?

Position specimen correctly.

Was 100% calibration
performed correctly?

Attach White Calibration Plate
correctly and perform 100%
calibration correctly using
the appropriate calibration
standard (air or distilled water).

Was zero calibration
performed correctly?

Attach White Calibration
Plate correctly, block all light
from reaching the receptor
window, and perform zero
calibration correctly.

Was measurement mode
set to transmittance?

By referring to the operation
manual of the software, perform
the operation correctly.

—

Data input/output between
the Spectrophotometer
and a computer cannot
be performed.
Commands cannot be input
to the Spectrophotometer
from a computer.

Is the USB cable connected
correctly to both the
Spectrophotometer
and the computer?

Connect the USB cable correctly
bitween the Spectrophotometer
and the computer.

I s t h e s o f t wa r e o p e ra t i n g
correctly?

By referring to the operation
manual of the software, perform
the operation correctly.

—

Set POWER switch of
Spectrophotometer to OFF
and then set it back to ON.

«
...
31
32
33
34
35
...
»

Содержание CM-3700A











































Отзывы:

Нет отзывов

Похожие инструкции для CM-3700A

Бренд: WAGER Страницы: 22

Бренд: Abbott Страницы: 296

Бренд: OHAUS Страницы: 84

Бренд: Hama Страницы: 6

Бренд: Roland Страницы: 15

Бренд: janitza Страницы: 6

Бренд: janitza Страницы: 36

FG-3000R Series

Бренд: Nidec Страницы: 8

Бренд: IFM Страницы: 38

Бренд: Hanna Instruments Страницы: 28

Бренд: Lutron Electronics Страницы: 23

Бренд: Televes Страницы: 2

Бренд: SPEEDMATE Страницы: 3

Бренд: Badger Meter Страницы: 20

Бренд: hager Страницы: 4

Бренд: Keysight Страницы: 41

Бренд: BEKA Страницы: 13

Бренд: Tektronix Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды