background image

E-2

II. Installation space (unit: mm (inch))

bizhub C3850 + PF-P13 + DK-P03

III. Pre-installation check items

1. Select a level and stable place for installing the 

machine.

2. Be sure to use a power source of the voltage and 

frequency indicated in the product specifications. 
Ensure that the current carrying capacity of the 
power outlet is at least equal to the current listed 
in the product specifications.

3. Power the machine directly from a dedicated 

power outlet. (Do not use an extension cord.)

4. Do not plug or unplug the power cord with wet or 

dirty hands, otherwise you may get an electric 
shock.

5. Avoid a hot and humid environment, or a place 

exposed to direct sunlight.

6. Avoid a dusty location, or a place near volatile 

and flammable substances.

7. Avoid a poorly ventilated place.

IV. Notes on using touch panel

Be sure to instruct users on the following points.
    • This machine uses a capacitive touch panel. 

When you touch the touch panel, use your fin-
ger or the stylus pen for the capacitive touch 
panel. If you touch the panel using your nail or 
a pen tip instead of using your finger or the sty-
lus pen, the touch panel does not respond nor-
mally. 

    • Pressing the touch panel hard may cause dam-

age.

    • Do not strongly press the panel or press it using 

the sharp tip of mechanical pencils.

    • The key is a finger tapping (quick light touch 

using a finger) operation.

809 (31-7/8)

14

53 (

57

-3

/16)

555 

(21-7/8)

254 

(10)

1062 (41-13/16)

1014 (39-15/16)

884 

(34-13/16)

48 

(1-7/8)

3

35 

(13-

3/1

6)

385

 

(1

5-

3/

16

)

73

(2

8-

7/8

)

Содержание Bizhub C3350











Отзывы: