Kongskilde GMT 3205 L P Скачать руководство пользователя страница 107 | Manualshive

Страница: 107 / 190

background image

7 - MAINTENANCE

7 - MAINTENANCE

###_7_###

General information

General

WARNING

Avoid injury! Always do the following before
lubricating, maintaining, or servicing the ma-
chine.
1. Disengage all drives.
2. Engage parking brake.
3. Lower all attachments to the ground, or
raise and engage all safety locks.
4. Shut off engine.
5. Remove key from key switch.
6. Switch off battery key, if installed.
7. Wait for all machine movement to stop.
Failure to comply could result in death or se-
rious injury.

W0047A

WARNING

Moving parts!
Some components may continue to run after
disengaging the drive systems.

Make sure

all drive systems are fully disengaged and all
movement has stopped before servicing the
machine.
Failure to comply could result in death or se-
rious injury.

W0002A

Adequate lubrication and maintenance on a regular
schedule is vital to maintain your implement. To ensure
long service and efficient operation, follow the lubrication
and maintenance schedules outlined in this operator’s
manual. The use of proper, oils, grease, and filters, as
well as keeping the systems clean, will also extend the
implement and components life.

NOTICE:

Failure to complete the required maintenance

at the recommended intervals can cause unnecessary
downtime.

Use the intervals listed in the maintenance chart as guide-
lines when you operate in normal conditions. Adjust the
intervals when you operate in adverse environmental and
working conditions. Shorten the intervals for sandy, dusty,
and extremely hot operating conditions.

NOTICE:

While any company can perform neces-

sary maintenance or repairs on your implement,
KONGSKILDE strongly recommends that you use only
authorized KONGSKILDE dealers and products that meet
given specifications. Improperly or incorrectly performed
maintenance and repair voids the equipment warranty
and may affect service intervals.

7-1

«
...
105
106
107
108
109
...
»

Содержание GMT 3205 L P































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GMT 3205 L P

Бренд: Hanil Страницы: 60

Бренд: ZIGBEE Страницы: 6

Бренд: Daisy Страницы: 2

Below Ground Pool Cover Box

Бренд: Daisy Страницы: 3

Бренд: Parker Страницы: 39

Бренд: Gardol Страницы: 260

Бренд: York Fitness Страницы: 20

Бренд: Mackie Страницы: 34

Бренд: Mackworth Страницы: 38

Бренд: P&P Страницы: 6

Бренд: Yamaha Страницы: 139

Бренд: Yamaha Страницы: 19

Бренд: Yamaha Страницы: 32

Бренд: Yamaha Страницы: 45

Бренд: Fast Страницы: 60

Бренд: GE Страницы: 37

Бренд: MAKSIWA Страницы: 155

Бренд: Measumax Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды