manualshive.com logo in svg

Kongsberg cJoy OT, Руководство оператора

Поделиться
Скачать
Kongsberg cJoy OT Скачать руководство пользователя страница 46

Kongsberg cJoy OT

Speed sensors

The second dialog for speed sensors is used to enable and disable speed sensors, and enter
a manual speed value that will be used to provide the system with speed information.

To display this second dialog, press the

Sensor enable

button once more.

Figure 9

Sensor Enable input dialog for speed senors

Use

Shows which speed sensors or manual speed value are being used by the system
(see

Speed sensors

on page 102).

•

Green

— In use

•

Grey

— Not in use

Manual SPD

Allows you to enable (

On

) and disable (

Off

) the manual speed value entered

in the

Value

field.

This value is used in the optional

Autopilot

and

Seismic Track

modes.

Value

Allows you to enter a manual speed value. Within the configured range the value
can be increased and decreased in 0.1 metre/second or 0.1 knot steps (see

Entering

and enabling a manual speed value

on page 103).

46

385585/C

Содержание cJoy OT

















































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды