Kongsberg cJoy OT Скачать руководство пользователя страница 27

Страница: 27 / 208

User interface

•

Grey

— Within the limits

•

Yellow

— Warning limit exceeded

•

Red

— Alarm limit exceeded

Autopilot mode

In the optional

Autopilot

mode, the joystick setpoint and joystick

response for the surge axis is indicated as described for

Joystick

mode (see

Joystick mode

on page 25).

The direction of the joystick tilt is indicated as described for the
axis under joystick control in

Mixed Joystick/Auto

modes (see

Mixed Joystick/Auto modes

on page 26).

View area

The View area is used to show operational views, input dialogs (see

Input dialogs

page 40), and system views and input dialogs.

Operational views

The operational views present information relevant for system operation.

View selection

Operational views are selected and cyclically displayed in the View area of the display
by pressing the

Views

button one or more times until the required view is displayed.

The sequence in which the views are displayed is as follows:

• Main view

• Position-reference System view (option)

• Thruster view

• Sensor view

• Power Consumption view (option)

385585/C

Содержание cJoy OT

















































































































































































































Результаты поиска

Содержание cJoy OT

Отзывы:

Бренды по названию

Популярные бренды

Kongsberg cJoy OT, Руководство оператора

Результаты поиска

Содержание cJoy OT

Отзывы:

Бренды по названию

Популярные бренды