Kolin KLG-IF40-2C1M Скачать руководство пользователя страница 34

Страница: 34 / 36

7.2 Routine Maintenance

WARNING!

①

. Do turn off the unit and cut off the main power supply when cleaning the air conditioner,

otherwise electric shock may happen.

②

. Do not make the air conditioner wet or electric shock may be lead; Ensure that the air

conditioner will not be cleaned by water rinsing under any circumstance.

③

. Volatile liquid like thinner or gasoline would damage the appearance of air conditioner. (So, only

soft dry cloth and wet cloth moistened by neutral cleaning fluid could be used to clean the

surface panel of air conditioner.)

(1). Clean the air filter(once every 2 weeks)

1. Disassembly of air filter

Open screw caps at both sides

according to direction in fig. 1. Remove the

screws at both sides of air-in panel with

screwdriver. After opening the air-in panel

unscrew the screws fixing the air filter.At last

pull out the air filter from the arrow direction.

．

Cleaning the filter

Slightly flat the filter or clean the filter

with electric cleaner.If too much dust on the

filter,clean it with a little neutral detergent or

warm water.After that,dry the filter and

reinstall it,as shown in Fig.8.

NOTE: Do not dry the filter by exposing it

under direct sunshine or near a heating

oven, or it may get deformed.

Содержание KLG-IF40-2C1M





































Результаты поиска

Содержание KLG-IF40-2C1M

Отзывы:

Похожие инструкции для KLG-IF40-2C1M

Бренды по названию

Популярные бренды

Kolin KLG-IF40-2C1M, Руководство пользователя

Результаты поиска

Содержание KLG-IF40-2C1M

Отзывы:

Похожие инструкции для KLG-IF40-2C1M

Бренды по названию

Популярные бренды