background image

安装步骤

INSTALLATION

清洗说明

CLEANING INSTRUCTIONS

适用于所有加工处理过的表面:以中性肥皂水清洗镀
层表面,再以干净的软布彻底擦干整个表面,许多清
洁剂,比如氨水、去污粉及洁厕灵等,会对电镀表面
造成伤害,切忌使用。

有磨损性的清洁用具或清洁剂也不可使用于科勒牌的
水龙头及其配件上。

All Finishes: Clean the finish with mild soap and warm 

water. Wipe entire surface completely dry with clean 

soft cloth. Many cleaners may contain chemicals, such 

as ammonia, chlorine, toilet cleaner etc. which could 

adversely affect the finish and are not recommended 

for cleaning.

Do not use abrasive cleaners or solvents on Kohler 

faucets and fittings. 

使用说明

轻轻打开把手,顺时针旋转为冷水,
逆时针旋转为热水。

手持使用花洒时,取下花洒,并拉出
软管。

如图

所示

,按下按钮

(15)

的不同位置

A

B

,可分别获得两种不同水流。按住

按钮

(16)

,暂停出水。

注意:不要用力过猛或拉出过长,以
免造成软管及接头损坏。

OPERATION INSTRUCTION

Turn on the handle gently. Turn clockwise 

for cold water, counter-clockwise for hot 

water.

If you want to use the sprayhead by hand, 

take the sprayhead and pull out the hose.

Press different position A or B of the 

button(15), you will get different water flow 

as shown. Press and hold the button(16), 

it will stop water flow. 

NOTE: 

Please pull it gently and do not 

draw out the spray hose too long, or you 

may damage the hose and connector.

INSTALLATION CHECKOUT

安装结果检查

检查并确保所有衔接处都已拧紧,确
保把手在关闭位置。打开主水源和排
水系统,检查并修理有漏水的接口。

将花洒

(13)

拆下,打开把手,让水流约

一分钟以清除杂质。关闭龙头,重新
装回花洒。

Ensure that all coupling nuts are tight. 

Ensure that the handle is in the off 

position. Turn on the main water supply 

and drain, and check for leaks. Repair 

as needed.

Remove the sprayhead(13). Run hot 

and cold water about one minute to 

remove any debris. Shut off the faucet. 

Reinstall the sprayhead.

13

维护与保养

CARE AND MAINTENANCE

Turn on the faucet, rub the sprayhead 

nozzles to dislodge debris.

To improve water flow, trun off the faucet. 

Disconnect the sprayhead. Remove and 

clean the screen(14) inside the sprayhead. 

Reinsert the screen and reconnect the 

sprayhead.

打开龙头,揉搓花洒喷嘴以清除杂质

当有杂质使水流变小时,关闭龙头,
取下花洒,取出里面的滤网垫片

(14)

并清洗。

清洗后重新装回即可。

如何安装水龙头

将装饰罩

(1)

穿过软管、牙管

(2)

置于水

龙头

(3)

底部。从厨盆上方将水龙头组

件插入台面安装孔中,使装饰罩底部
接触台面,且把手置于右边。

确保螺钉

(4)

部分旋入安装环

(5)

从厨

盆下方依次把垫片

(6)

及装有两个螺钉

的安装环装到牙管

(2)

上。调整水龙头

位置,使得花洒软管

(7)

在左边,与两

进水软管

(8)

左右对称。旋紧安装环直

至垫片紧贴厨盆底部,拧紧螺钉

(4)

固定水龙头。

将进水软管

(8)

接到水源上,贴有蓝点

标识的软管连接冷水,贴有红点标识
的软管连接热水。

重锤

(9)

装到花洒软管

(7)

上。将快接

(10)

有螺纹一端旋紧到花洒软管上,另

一端连接到出水软管

(11)

上。调整重锤

的位置使其距龙头底面距离合适,确
保抽拉顺畅,用扎带

(12)

固定重锤的位

置。

How to Install the Faucet

Slide the escutcheon(1) over the hoses 

and shank(2) until it contacts the faucet 

(3) bottom. From upside of the sink,

insert the faucet assembly into the

mounting hole until the escutcheon

bottom is against the deck. Ensure the

handle is on the right.

Partially thread two screws(4) into the 

threaded ring(5). From underside of the 

sink, place the washer(6) and threaded 

ring with two screws over the shank(2). 

Position the faucet so that the spray 

hose(7) is on the left, the spray hose and 

two supply hoses(8) are symmetrical. 

Thread the threaded ring onto the shank 

until the washer contacts the underside 

of the sink. Tighten two screws(4) to 

secure the faucet to sink.

Attach the hoses(8) to water supplies. 

The hose with blue dot should be 

connected to cold water. The hose with 

red dot should be connected to hot 

water.

Slide the weight(9) over the spray hose 

(7). Tighten the connector(10) onto the 

spray hose, and then install it to the 

outlet hose(11). Adjust the weight to the 

appropriate position, check for smooth 

operation, and secure it with a loose 

cable tie(12). 

1

4

7

9

12

12

9

8

3

5

2

6

11

10

7

A

B

16
15

1434194-2-A            

3  

1434194-2-A            

2

14

Отзывы: