Kohler SFGLD360 Скачать руководство пользователя страница 235

Страница: 235 / 314

PRODUCT INFORMATION

INDEX

DATE

Dep. 2

IO-G-M-00-019e G

January 2016

MAINTENANCE OF NATURAL GAS ENGINE SFGLD

STAND-BY

1/6

1. MAINTENANCE PROGRAM

The information in this maintenan ce program is complemented with product information document

IO-G-M-00-060e

, General Maintenance Guidelines for Gas Engines.

KOHLER

has developed this maintenance program to ensure optimum performance of your engine. Given that

strict adherence to thi s program will benefit you, it is es sential that you follo w the in structions detailed in this

manual. Failure to do so may not only jeopardize

KOHLER

’s warranty, but also restrict you from obtaining the

best performance for equipment.

The maintenance intervals listed in this section do not in any way imply an obligation on behalf of

KOHLER

and are given only as a guide to use

rs for mai ntenance scheduling. Users will take into account op erating

conditions and demands to determine the maintenance operations that should be carried out more frequently than

stated on the schedule. In all cases, the number of hours specified are reasonable limits, which should not be

exceeded in order to ensure that the engine works correctly. If the engine maintenance schedule is not adhered

to then the warranty of the same may be cancelled. This document and product information document

IO-G-M-00-060e

should be studied carefully before the engine is started up for the first time.

NOTE

Any Check-Inspection may require a corrective operation if the element in question requires one.

IMPORTANT

The maintenance jobs described below (identified with as an “E” type task) must be regarded as “additive” to each other.

Accordingly, the performance of every “E

” job implies that all previous “E

i-1

”, every time as the frequency indicates it.

This will require the availability of such materials and labour as may be necessary at each stage.

5.1.13

O&M_2.002211.810_A_10_2016

Содержание SFGLD360



























































































































































































































































































































Результаты поиска

Содержание SFGLD360

Отзывы:

Похожие инструкции для SFGLD360

Бренды по названию

Популярные бренды

Kohler SFGLD360, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание SFGLD360

Отзывы:

Похожие инструкции для SFGLD360

Бренды по названию

Популярные бренды