background image

-4-

Fig.#7

7

Firmly press the toilet gasket onto the
toilet outlet of plastic trap.

Wax ring type toilet gasket

should not be installed at temperatures
less than 21 C.

If you are using a toilet

gasket with an integral plastic sleeve,
make sure the gasket is positioned
with the sleeve facing away from the
toilet.

NOTE 1:

NOTE 2:

o

1

21

2

o

C

Plastic Trap Outlet

Toilet Gasket

Fig.#8

8

Install plastic to ground and mounted
with 3 set of bolts

firmly.

(not supplied)

3

(

)

NOTE:

Must use the toilet installation

gasket ring (not supplied) to seal the
area where the waste pipe contacts
the construction section to avoid
leakage.

(

)

Thread the supply hose onto the fill valve shank. See Fig.#9

9

Fig.#9

9

Install the toilet seat according to the seat manufacturer's
installation instructions. See Fig.#10

10

Fig.#10

10

Insert the inlet hose of the toilet and the power line and inlet
hose of the bidet seat into the decorative cap. Insert the cap
firmly into the toilet. See Fig.#11

11

Fig.#11

11

Fig.#12

12

Carefully align and lower the bowl. Apply weight to the bowl
rim to let the outlet insert into plastic trap. See Fig.#12

12

Outlet

Plastic Trap

1397913-T01-B

Содержание S-TRAP K-23188T-HC











Отзывы: