1212710-2A-A
2
1212710-2A-A
3
CLEANING INSTRUCTIONS
All Finishes: Clean the finish with mild soap and warm water. Wipe entire surface completely dry with clean soft
cloth. Many cleaners may contain chemicals, such as ammonia, chlorine, toilet cleaner etc, which could adversely
affect the finish and are not recommended for cleaning.
Do not use abrasive cleaners or solvents on Kohler faucets and fittings.
INSTALLATION
INSTALLATION CHECKOUT
How To Install The Lift Rod
Unscrew the lift rod knob(1) from the lift rod(2). Insert the lift rod into the
groove of the faucet through the underside hole . Screw the lift rod knob
to the lift rod, tightened by hand.
NOTE:
There is no lift rod assy in 14404T.
How To Install The Drain (Only For 14402T)
Uninstall the stopper(10), drain flange(12) and washer(13) from drain
body(17). Slide washer onto the underside of the drain flange. Uninstall
the tailpiece(19) from the drain body. Supply enough tape or sealant to
tailpiece thread. Reinstall the tailpiece. Insert the drain body with
gasket(14), steel washer(15) and locknut(16) into the lavatory from
underside, with the drain lever hole(18) facing the rear.
NOTE
: If necessary, apply a ring of plumbers putty around the underside
of the drain flange, instead of using washer(13).
Thread the drain flange onto the drain body. Tighten the locknut from the
underside of the lavatory by hand. Place stopper into drain body, aligning
the flat side of stopper hole(11) with the drain lever hole.
Loosen the screw(25) on the latch(23), take off the latch. Remove the
retaining nut(21). Fit the plastic washer(20) and retaining nut onto the ball
lever rod(22). Insert the ball lever assembly into the drain lever hole(18)
and through the stopper hole. Tighten the retaining nut.
Be sure that the ball lever rod points to the back of the lavatory, tighten
the locknut.
NOTE
: Do not reposition the drain after the locknut is tightened, or you
may break the putty seal. Remove any excess putty.
How To Install The Faucet
Install the stud(3) into the faucet body(6). Put the washer(4) into the
bottom of body through the flexible hoses(5) and the stud. Insert hoses
and stud into the hole of lavatory. Position the faucet. From underside of
the lavatory, fit the bracket(7) and washer(8) on the stud. Secure the
faucet by tightening nut(9).
Attach the hoses to water supplies. When facing front of faucet, the left
hose is hot water, the right hose is cold water.
How To Install The Lift Rod Kit
Select the connection of the drain and the lift rod according the
dimension of lavatory.
Way 1: Select the latch(23)
Insert the ball lever rod(22) into the bigger hole(24) of the latch(23). Insert
the lift rod into the other hole of latch. Position the lift rod, ensure the
distance between the lift knob and the faucet body is about 10mm. Push
the ball lever rod(22) down to the open position. Tighten the screw(25) on
the latch.
Way 2: Select the link kit(26, 27 & 28).
According to the lift rod length, bend the link(27). Connect the link onto
ball lever rod with ‘V’ clip(28). Slide lift rod into the hole on link. Position
the lift rod, ensure the distance between the lift knob and the faucet body
is about 10mm. Push the ball lever rod(22) down to the open position.
Tighten thumb screw(26).
Connect the tailpiece to the trap. The tailpiece should extend 25mm to
50mm into the trap.
1
2
3
9
4
5
6
7
8
12
13
16
10
15
11
17
18
14
19
20
21
22
25
23
18
Apply Plumbers Putty
23
25
26
27
22
22
2
2
28
24
29
30
31
32
33
Drain Body
35
36
37
34
Ensure that all connections are tightened and the handle is in the off
position. Open the drain. Turn on main water supply and check for leaks.
Repair as required.
Remove the aerator(34). Turn on the faucet. Run the hot and cold water
through the spout for about one minute to remove any debris. Remove
any debris from the aerator. Shut off the faucet and reinstall the aerator.
Replacing the Washer and Piston Kit
Turn counterclockwise to uninstall the stopper(35). Take out washer(36).
Replace with a new one. Turn counterclockwise to uninstall the piston
kit(37). Replace with a new one. Reinstall stopper and washer.
How To Install The Drain (Only For 14404T)
Remove the locknut(33), plastic washer(32), rubber gasket(31) from the
drain body. Insert the drain body into the lavatory. Reinstall the rubber
gasket(Tapered side up), plastic washer and locknut back to the drain
body in turn. Tighten the locknut.
Note
: If needed, apply a ring of plumbers putty or other sealants around
the underside of the drain flange(29), instead of using rubber washer(30).
Do not reposition the drain after the locknut is tightened, or you may
break the putty or sealant seal. Remove any excess putty.
