Kohler Mira Event XS Скачать руководство пользователя страница 3

Страница: 3 / 40

1293809-W2-E

DO NOT

switch the shower on if water starts leaking from the shower

case. Isolate the electrical supply to the shower immediately.

10.

DO NOT

switch the shower on if the case appears to be damaged

or incorrectly fitted. Isolate the electrical supply to the shower

immediately.

11.

DO NOT

increase the power setting or adjust the temperature

control rapidly while using the shower.

12.

DO NOT

switch the shower off and back on while standing in the

water flow.

13.

DO NOT

change the handset model. Fit only shower heads

recommended by Mira and do no fit any additional device to restrict

the water outlet flow.

14. When adjusting the handset mode, point handset away from body

and make sure that the water temperature has stabilised before

continuing to shower.

15. Use caution when altering the water temperature, always check

the temperature before continuing to shower.

16. Switch the shower off at the electrical isolating switch when not in

use. This is recommended with all electrical appliances.

17. Installation of the shower must be carried out in accordance with

these instructions by qualified, competent personnel. Read all

instructions before installing the shower.

18. Isolate the electrical and water supplies before commencing

installation. The electricity must be isolated at the consumer unit

and the appropriate circuit fuse removed, if applicable. Mains

connections are exposed when the cover is removed.

19.

DO NOT

install the shower in areas with high humidity and

temperature (i.e. Steam rooms and saunas).

20.

DO NOT

install the shower where it may be exposed to freezing

conditions. Ensure that any pipework that could become frozen is

properly insulated.

21.

DO NOT

connect the outlet of the shower to any tap, control valve,

trigger operated handset or showerhead other than those specified

for use with this shower as the outlet acts as a vent for the tank

body. Only Kohler Mira recommended accessories should be used.

Содержание Mira Event XS









































Результаты поиска

Содержание Mira Event XS

Отзывы:

Бренды по названию

Популярные бренды

Kohler Mira Event XS, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Mira Event XS

Отзывы:

Бренды по названию

Популярные бренды