安装步骤
INSTALLATION
1435820-2-A
3
1435820-2-A
2
龙头本体背面标有“
LEAD FREE
”字样，即产品符
合美国
AB1953
法令的要求。
"LEAD FREE" is marked on the back of the faucet
signifying its compliance with the United States
AB1953
．
如何安装水龙头
将 底 座
(1
， 有 泡 沫 的 面 朝 下
)
穿 过 软
管、牙管
(2)
置于水龙头
(3)
底部。从厨
盆上方将水龙头组件插入台面安装孔
中，使底座底部接触台面，且把手置
于右边。
确保螺钉
(4)
部分旋入安装环
(5)
。
从厨
盆下方依次把橡胶垫片
(6)
、垫片
(7)
及
装 有 两 个 螺 钉 的 安 装 环 装 到 牙 管
(2)
上。调整水龙头位置，使得花洒软管
(8)
在左边，与两进水软管
(9)
左右对
称。旋紧安装环直至垫片紧贴厨盆底
部，拧紧螺钉
(4)
以固定水龙头。
将单向阀接头
(10)
拧紧到供水阀上，
接着将进水软管
(9)
连接到单向阀接头
上，贴有“
COLD
”标签的软管接冷
水，另一根软管连接热水。
将
重锤
(11)
装到花洒软管
(8)
上，调整
重锤位置使其距龙头底面距离合适，
扣紧卡扣。将花洒软管上的快接
(12)
连
接到出水软管
(13)
上。
How to Install the Faucet
Slide the base(1, foam side down) over
the hoses and shank(2) until it contacts
the faucet(3) bottom. From upside of the
sink, insert the faucet assembly into the
mounting hole until the base bottom is
against the deck. Ensure the handle is
on the right.
Partially thread two screws(4) into the
threaded ring(5). From underside of the
sink, place the rubber washer(6), washer
(7) and threaded ring with two screws
over the shank(2). Position the faucet so
that the spray hose(8) is on the left, the
spray hose and two supply hoses(9) are
symmetrical. Thread the threaded ring
onto the shank until the washers contact
the underside of the sink. Tighten two
screws(4) to secure the faucet to sink.
Connect and tighten the check valve
housings(10) to water supplies. Connect
and tighten the supply hoses(9) to the
check valve housings. The supply hose
with “COLD” label should be connected
to cold water. Another hose should be
connected to hot water.
Put the weight(11) onto the spray hose
(8). Adjust the weight to the appropriate
position and squeeze to connect the
clasp. Connect the connector(12) of the
spray hose to the outlet hose(13).
INSTALLATION CHECKOUT
安装结果检查
检查并确保所有衔接处都已拧紧，确
保把手在关闭位置。打开主水源和排
水系统，检查并修理有漏水的接口。
将花洒
(14)
拆下，打开把手，让水流约
一分钟以清除杂质。关闭龙头，重新
装回花洒。
Ensure that all coupling nuts are tight.
Ensure that the handle is in the off
position. Turn on the main water supply
and drain, and check for leaks. Repair
as needed.
Remove the sprayhead(14). Run hot
and cold water about one minute to
remove any debris. Shut off the faucet.
Reinstall the sprayhead.
1
4
7
8
9
3
5
12
10
11
2
6
13
维护与保养
CARE AND MAINTENANCE
Turn on the faucet, rub the sprayhead
nozzles to dislodge debris.
To improve water flow, trun off the faucet.
Disconnect the sprayhead. Remove and
clean the screen(16) inside the sprayhead.
Reinsert the screen and reconnect the
sprayhead.
打开龙头，揉搓花洒喷嘴以清除杂质
当有杂质使水流变小时，关闭龙头，
取下花洒，取出里面的滤网垫片
(16)
并清洗。
清洗后重新装回即可。
。
清洗说明
CLEANING INSTRUCTIONS
适用于所有加工处理过的表面：以中性肥皂水清洗镀
层表面，再以干净的软布彻底擦干整个表面，许多清
洁剂，比如氨水、去污粉及洁厕灵等，会对电镀表面
造成伤害，切忌使用。
有磨损性的清洁用具或清洁剂也不可使用于科勒牌的
水龙头及其配件上。
All Finishes: Clean the finish with mild soap and warm
water. Wipe entire surface completely dry with clean
soft cloth. Many cleaners may contain chemicals, such
as ammonia, chlorine, toilet cleaner etc. which could
adversely affect the finish and are not recommended
for cleaning.
Do not use abrasive cleaners or solvents on Kohler
faucets and fittings.
使用说明
轻轻打开把手，顺时针旋转为冷水，
逆时针旋转为热水。
手持使用花洒时，取下花洒，并拉出
软管。
如图
所示
，按下按钮的不同位置
A
或
B
，可分别获得两种不同水流。
注意：不要用力过猛或拉出过长，以
免造成软管及接头损坏。
OPERATION INSTRUCTION
Turn on the handle gently. Turn clockwise
for cold water, counter-clockwise for hot
water.
If you want to use the sprayhead by hand,
take the sprayhead and pull out the hose.
Press different position A or B of the button,
you will get different water flow as shown.
NOTE:
Please pull it gently and do not
draw out the spray hose too long, or you
may damage the hose and connector.
A
B
15
14
