background image

13

Service Precleaner

Wash and reoil the precleaner every 

25 hours

 of

operation (more often under extremely dusty or dirty

conditions).

1. Unhook the four retaining straps and remove the

upper blower housing and screen assembly. See

Figures 8 and 9.

2. Remove the foam precleaner from the paper

element. See Figure 17.

Figure 17. Removing Precleaner from Paper

Element.

3. Wash the precleaner in warm water with detergent.

Rinse the precleaner thoroughly until all traces of

detergent are eliminated. Squeeze out excess

water (do not wring). Allow the precleaner to air dry.

4. Saturate the precleaner with new engine oil.

Squeeze out all excess oil.

5. Clean the air cleaner base area, upper blower

housing, and screen assembly of any debris

accumulation. If required, the screen assembly may

also be separated from the upper blower housing

by unsnapping it from the underside. See Figures

18, 19, and 20. Check all parts for wear, cracks, or

damage. Replace any damaged components.

Figure 19. Unsnapping Screen Assembly.

Figure 20. Removing Screen Assembly.

6. Reinstall the precleaner over the paper element,

outside the element retaining strap.

7. Reinstall the upper blower housing and screen

assembly. Secure with the four retaining straps.

8. When precleaner replacement is necessary, order

Kohler Part No. 

66 083 03-S

.

Service Paper Element

Every 

100 hours

 of operation (more often under

extremely dusty or dirty conditions), replace the paper

element.

1. Unhook the four retaining straps and remove the

upper blower housing and screen assembly. See

Figures 8 and 9.

2. Remove the foam precleaner from the paper

element. See Figure 17. Service or replace the

precleaner.

Figure 18. Clean Away Debris.

Содержание Aegis 20 HP





















Отзывы: