manualshive.com logo in svg

Kohler 15RYG, Руководство по установке

Поделиться
Скачать
Kohler 15RYG Скачать руководство пользователя страница 29

TP-6329 8/07

29

Section 3 Installation Instructions

4. Check that the fuel system is set up for the fuel

being used (natural gas or LP).

a. Check the orientation of the fuel regulator and

check the hang tag attached to the regulator.
The fuel regulator is installed pointing up for
natural gas and down for LP gas.

See

Figure 3-10.

b. Use the following procedure to convert the fuel

system, if necessary.

1

1. Fuel system

Figure 3-9

Generator Set Fuel System Location
(enclosed unit shown)

1. Solenoid valve
2. Secondary regulator (shown pointing down for LP)
3. Fuel supply connection

Note:

UL 2200 listed units include a second fuel valve.

1

GM39123

2

3

Figure 3-10

Fuel System (LP gas setup shown)

3.8.1

Fuel Conversion Procedures

When converting the generator set to operate with LP
gas, remove the internal spring from the secondary
regulator and rotate the regulator to point down. To
operate the generator set on natural gas, install the
spring and rotate the regulator to point up.

LP Fuel Conversion Procedure

Use the following steps to set the fuel system for LP gas:

1. Remove the fuel regulator cover plug.

See

Figure 3-11.

SB-527

1. Fuel regulator
2. Spring
3. Adjustment screw
4. Cover plug

1

2

3

4

Figure 3-11

Fuel Regulator, Typical

2. Remove the adjustment screw and spring from the

fuel regulator.

Save the adjustment screw and

spring for possible conversion back to natural gas.

3. Reinstall the cover plug.

4. Rotate the regulator to point down as shown in

Figure 3-10.

5. Disconnect leads 65 and 70A at the quick connects

in the wiring harness.

6. Connect a manometer to check the fuel supply

pressure on the carburetor side of the regulator.

7. Adjust the fuel supply pressure with the generator

set running at full load.

Rotate the adjustment

screw on the primary fuel regulator until the
manometer indicates a fuel pressure of 7--11
inches water column. Pressures below 7 inches
water column may result in poor response to load
changes or lack of power.

Содержание 15RYG

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды