Kohler 10EOZ Скачать руководство пользователя | Manualshive

Страница: 29 / 80

background image

TP-6053 7/04

17

Section 4 Fuel System

4.7 Governor

The centrifugal, mechanical governor keeps the engine
speed constant by automatically adjusting the amount
of fuel supplied to the engine according to changes in
the load. No regular service is required on the governor.
The factory adjusts the governor during run-in, and
further adjustment should not be needed unless poor
governor control develops after extended generator
usage.

60 Hz

generator sets are designed to operate at

57--63 Hz, 1800 rpm under full load and 1890 rpm under
no load.

50 Hz

generator sets are designed to operate at

47--53 Hz, 1500 rpm under full load and 1590 rpm under
no load.

Check the engine speed using a frequency meter
connected to the load leads. Loosen the locking nut on
the speed adjusting screw. Turn the screw clockwise to
increase the speed and frequency.

Turn the screw

counterclockwise to decrease the speed. Tighten the
locknut at the new setting. See Figure 4-8 or Figure 4-9.

DK-250000B-D

1

2

1. Locknut
2. Speed adjusting screw

Figure 4-8

Governor, 5EOZ/4EFOZ

ED-250000A-N

1

2

1. Locknut
2. Speed adjusting screw

Figure 4-9

Governor, 8/9/10EOZ and 6.5/8/9EFOZ

«
...
27
28
29
30
31
...
»

Содержание 10EOZ

















































































Отзывы:

Нет отзывов

Похожие инструкции для 10EOZ

Бренд: ZOLL Страницы: 5

Бренд: Accu-Chek Страницы: 3

Бренд: iBin Страницы: 2

Бренд: Yardistry Страницы: 9

Бренд: Tascam Страницы: 80

Бренд: Tascam Страницы: 2

Бренд: Walker Страницы: 24

Бренд: Baoding Longer Precision Pump Страницы: 6

Бренд: Hammer Страницы: 42

Бренд: Panta Safe Light Страницы: 2

Бренд: Calrec Страницы: 70

Бренд: Jensen Страницы: 2

Бренд: Raven Страницы: 48

Бренд: Pacific Страницы: 16

Бренд: Additel Страницы: 107

Бренд: Aspect Medical Systems Страницы: 104

Бренд: Hupfer Страницы: 153

Wallach UltraFreeze

Бренд: Cooper Surgical Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды