7. THE ALARM SYSTEM SETUP.
Default factory settings and available settings are listed in Table 2 of chapter 7.4. If default settings are not suitable there are 2 ways to change
them.
7.1. MANUAL SETUP:
a)
turn the override mode ON by entering the PIN
;
b)
the system LED will start frequently flashing;
c) within 8 minutes of the override mode being turned ON, in the same way as before entering the PIN, enter the FN number of the function you
want to change;
d) if the correct FN number was entered, the system indicates the current SN value by 5 separate series of direction indicator flashes (with a pause
of 2 seconds between the series), the number of flashes in each series corresponds to current SN value;
e) the assigned control time is extended for another 8 minutes. No flash of direction indicators means either incorrect FN entry or the 8 minute
control time has elapsed;
f) if the FN has not been entered due to the 8 minute control time being elapsed, repeat the steps starting from a);
if the FN has not been entered due to a mistake, wait until the system LED starts flashing frequently and re-enter the FN code;.
g) if the SN does not mach your needs you can change it. To change it do the following: when the system indicates the current SN value by 5
separate series of flashes press and hold down the override button or turn ON the ignition. The direction indicators start to flash by single
flashes every 3 seconds. When the number of flashes corresponds to the necessary SN value (wait a second after the last flash) release the
override button or turn OFF the ignition. The system confirms a new SN value entry by a long siren beep (0.5 second) and indicates a new SN
value by 5 separate series of direction indicator flashes. The control time is extended for another 8 minutes;
The Manual Setup sequence summary is listed in Table 1.
Table 1
7.2. THE ALARM SYSTEM SETUP BY COMPUTER.
For professional fitting it's recommended that the PULSE-LATCHER device, a PC and the 'CAdmin' software for an alarm system setup are
used. This way it's possible to speed up the installation, to update the alarm system database with a new car's data and possible to store the records
about changed settings of each installation. To update an alarm system with the help of a PC do the following steps:
a) check
the 'CAdmin' software is present on your PC or download it from www.kodinis.lt, http://www.kodinis.lt/en/products/Car-Alarm-System-
Accessories
;
b) connect
an alarm system to the computer by using the PULSE-
LATCHER device as seen in diagram (see chapter. 4);
c) t
urn ON the car alarm override mode by entering the PIN
;
d) w
ithin 8 minutes start the 'CAdmin' software with the PULSE-
LATCHER device connected
;
e) create
a new installer account or login with an existing one
;
f)
click
on the “Clients DB” icon (see Fig. 3-A)
;
g) create
an account for the new client by clicking on “New client”
button;
h)
Fill up the fields in the “Client data” form, select the correct type of
alarm system and serial number according to the information sticker
(see Fig. 1) and click on “OK”;
i)
m
ake a double click on this then a newly created client record and
table with the alarm system default settings will appear (see Fig. 3-B);
j)
t
o make a settings change click on the “Change settings” icon (see
Fig. 3-C) and from the options displayed click on the options you
want (by clicking on their selection circles). When they are filled in
you have chosen that option (see Fig. 3-D);
k) w
hen all the changes are made click on the “Change settings” icon once again to disable changing opportunity and click on the “Update CA
Settings” icon (see Fig. 3-E) to start the Car Alarm settings update procedure;
l)
i
f the alarm system setup mode is left idle for more than 8 minutes (the control time) the system will automatically exit the setup mode. To go
back into the setup mode you must re-enter the PIN
.
7.3. THE ALARM SYSTEM LEARNING.
For adaptation of vehicle alarm system the Central Lock action sequence can be used
computer learning
,
automatic learning
or
manual
learning:
Computer learning
is advanced, but it is much more precise and reliable.
=
enter
the PIN code if control time is elapsed;
=
connect
'
GN6Ib
'
to PC using the „PULSE-LATCHER” device;
=
start
'
Cadmin
'
software and press the button
'
OSC
GN6IA
'
on software window;
=
following the software instructions read out the sequences of pulses are generated on '
GN6Ib
' inputs during the Central Lock is
locked and unlocked;
=
read pulses will be displayed on the computer display. According with these pulses adjust the pulse identification parameters
;
=
a
fter adjustment send the data to the alarm system;
=
these pulse parameters of the specific vehicle may be stored in a file, so in case installation of '
GN6Ib
' in vehicle with the same
Central Locking System it will be no need to read out the pulses. It will be enough to open stored file and send the data to '
GN6Ib
';
Automatic learning
is more simple (no computer is needed), but less precise and reliable because the installer has no chance to observe
the processes on the alarm system inputs. The automatic learning does not learn the pulses on input 'CONDITION2'.
=
if FN
=54, SN=4 is selected,
the system switches to automatic learning mode. The system siren emits the series of single or double
CONDITION
ACTION
CONTROL
TIME
DIRECTION
INDICATORS
SIREN
SYSTEM
LED
-
/ door opened
PIN ENTRY
-
Long flashes /
double flashes
PIN entered
FN
ENTRY
FN is entered, the override
button is not pressed /
ignition is turned OFF
SN
CHECK
FN is entered, the override button
is pressed / ignition is turned ON
SN
CHANGE
8 minutes
Frequent flashes
-
-
-
-
5 series of flashes (2 second pause
between series) number of flashes
in series
corresponds to SN value
-
FN=11
ENTRY
Long beep confirms
new SN value
8 minutes
Single flashes
every 3 seconds
8 minutes
Long flashes /
double flashes
Setup
is over
Long flashes /
double flashes
8 minutes
Frequent flashes
-
-
-
A
F
C
E
B
Fig. 3. 'Cadmin' software. Window of settings.
D
