Kodak Prosper S10 Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 39

Kodak Prosper S10 Скачать руководство пользователя страница 30

30

Kodak Prosper

S10 Printer

Chapter 3. Printer Maintenance

Filter Replacement

Filter Replacement

This section gives the procedures to replace the print station cooling fan
filter, PIC box HEPA filter, and PIC box printhead air filter.

Replace Print Station Cooling Fan Filter

On the print station, replace the cooling fan filter as necessary, so that the
print station continues to operate correctly (Figure 21).

CAUTION

Turn off the print station before the cooling fan filter is replaced. Damage
to the print station from dust can occur.

1.

Do “Turn Off the Print Station” on page 16.

2.

Open the print station front door.

3.

Remove the old filter from the bracket.

a.

Hold the filter by both sides and push up/down or left/right until
one edge clears a bracket.

b.

Lift the filter out of the bracket.

c.

Discard the old filter.

4.

Install the new filter in the bracket.

a.

Make sure the directional arrow on the filter points to the print
station.

b.

Put the top/bottom or left/right side of the filter into the bracket.

c.

Push up/down or left/right on the filter until the edge slips under a
bracket.

5.

Close the print station front door.

Figure 21

Print station air filters

Filters

Top/Bottom
edge

Left/Right
edge

«
...
28
29
30
31
32
...
»

Содержание Prosper S10








































Отзывы:

Нет отзывов