Kodak 8810 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 38

Kodak 8810 Скачать руководство пользователя страница 33

B-1

Appendix B: Safety and Regulatory

Information

Important Safety Information

CAUTION:

Use of controls or adjustments or performance of
procedures other than those specified in this manual may
result in injury and/or damage to the printer.

• The power outlet should be easily accessible and installed

near the printer.

• Position the power cable so that it cannot be pulled on or

tripped over.

• Never allow the power cable to contact hot surfaces.

• The power outlet must be grounded. An ungrounded outlet

can cause fire, electric shock, or harmful interference to
nearby electrical devices.

• Use only the power cable provided with the printer.

• Do not operate the printer with a damaged power cable.

• Always unplug the power cable from the printer before

cleaning or when the printer is not in use.

• If the printer has been dropped or damaged, make sure a

qualified service person examines the printer before you use
it.

• Do not block the filter openings on the printer cabinet.

• Do not expose the printer to moisture or water.

• Do not allow any foreign objects or liquids to fall or spill inside

the printer. Fire or electric shock could result.

• The thermal print head becomes extremely hot during normal

operation. Do not touch it.

• Alcohol pads are used to clean the thermal print head and

other internal printer components. In the United States, for
health, safety, and environment information, call
585-722-5151. Customers outside the U.S. can contact
KODAK Service and Support.

«
...
31
32
33
34
35
...
»

Содержание 8810







































Отзывы:

Нет отзывов