Kobold MAS Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 25

background image

MAS

MAS K05/0722

page 9

8.2 Output signals

The output signal is obtained from the 9-pin “D” connector. A 0 to 5 VDC output
signal linearly proportional to gas mass flow rate is standard. A 4-20 mA current
loop signal is optionally available.

8.3 Display

KOBOLD Mass Flow Meters, model MAS, for gases are available with an
integrated digital display, a remote digital display and without a digital display.
The decimal point on the version with digital display is set at the factory. It is
always a 3 ½-digit display.

Attention! KOBOLD Messring accepts no liability for any damage,
claims or faults resulting from operation with oxygen. MAS devices
can be manufactured oil and grease free if desired.

«
...
7
8
9
10
11
...
»

Содержание MAS


























Отзывы:

Нет отзывов

Похожие инструкции для MAS

Бренд: R.M. Young Страницы: 2

Бренд: Eaton Страницы: 87

Бренд: Eaton Страницы: 16

Бренд: Hach Страницы: 145

Бренд: Hach Страницы: 358

Polymetron 9582sc

Бренд: Hach Страницы: 280

Бренд: HACH LANGE Страницы: 15

Бренд: Stübbe Страницы: 12

SignalHawk SH-36S-PC

Бренд: BIRD Страницы: 137

Бренд: Konica Minolta Страницы: 92

Бренд: Tektronix Страницы: 116

Бренд: Sage Страницы: 75

AUER Atemluft 300 bar

Бренд: MSA Страницы: 52

Бренд: E+E Elektronik Страницы: 48

Бренд: DynAmp Страницы: 43

Бренд: IFM Страницы: 45

Бренд: Rodgers Страницы: 54

Бренд: SDT Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды