Kobelco KNW Series Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 54

background image

KIMA00H1 (0204)

11

1.8
Shutdowns

Shutdown conditions are indicated by a red ALARM light on the
control panel, and an appropriate message on the graphic display. In
addition, an audible alarm sounds when an alarm occurs. The alarm
beeper may be silenced by pressing ACK/Bell Cancel on the alarm
page. The Bell Cancel does not reset the alarm. A "DRY" relay
contact is provided as a combined signal for remote indication if any
alarm occurs. A table of setpoints is located on page 22.
The GT Terminal indicates the following shutdown conditions:

a. High 1st Discharge Air Temperature (Shutdown)

Warning: HOT 1st Discharge (Prealarm)
Indicates a problem with the first compressor stage.

b. Warning: HOT 2nd Suction (Prealarm)

High 2nd Suction Air Temperature (Shutdown)
Indicates a problem with the intercooler or cooling air flow.

c. Warning: HOT 2nd Discharge (Prealarm)

High 2nd Discharge Air Temperature (Shutdown)
Indicates a problem with the second compressor stage or a
problem with the intercooler.

d. Warning: HOT Air Discharge (Prealarm)

High Discharge Air Temperature (Shutdown)
Indicates a problem with the aftercooler or cooling air flow.

e. Warning: HOT Lube OIL (Prealarm)

High Lube Oil Temperature (Shutdown)
Indicates a problem with the lube oil cooling system.

f. Low Lube Oil Pressure

Indicates low lube oil level in sump, lube oil pump failure, fouled
cooler or piping, clogged oil filter, or improper setting of the relief
valve.

g. Lube Oil Pump Motor Overload

Indicates continued over-current operation of the oil pump motor,
problem with lube oil pump or motor, or high oil pressure.

h. Cooling Fan Motor Overload

Indicates continued over-current operation of the cabinet cooling
fan motor, problem with fan or motor. Also check for obstructed
air flow into or out of the cabinet.

i. Compressor Drive Motor Overload

Indicates continued over-current operation of the drive motor for
the compressor, excessive discharge pressure or a problem with
either compressor stage.

j. High Cabinet Temperature

Indicates an obstruction of the cooling air flow.

k. High Discharge Air Pressure

Indicates a problem with the capacity control system.

l. Main Starter Failure

Indicates a problem with the main starter or controls.

«
...
13
14
15
16
17
...
»

Содержание KNW Series























































Отзывы:

Нет отзывов

Похожие инструкции для KNW Series

Wireles One 25870

Бренд: Air Lift Страницы: 20

Бренд: STEELE PRODUCTS Страницы: 33

Бренд: NARDI COMPRESSORI Страницы: 56

Бренд: Trotec Страницы: 17

Бренд: Grizzly Страницы: 28

PORTABLE ELECTRIC AIR COMPRESSOR

Бренд: Mi-T-M Страницы: 60

Бренд: Parkside Страницы: 44

Бренд: Parkside Страницы: 85

Бренд: Vector Страницы: 7

Бренд: dbx Страницы: 2

AutoVelocity™ Dynamics and the dbx 160SL

Бренд: dbx Страницы: 8

Бренд: dbx Страницы: 30

Бренд: Atlas Copco Страницы: 28

Бренд: Atlas Copco Страницы: 30

Бренд: Atlas Copco Страницы: 32

Бренд: Campbell Hausfeld Страницы: 2

Бренд: Sparmax Страницы: 32

InTouch HA12P/110-4

Бренд: GEA Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды