KOBE
I N D U S T R I A L
POWER TOOLS
SAFETY INSTRUCTIONS
KOBE
I N D U S T R I A L
POWER TOOLS
SAFETY INSTRUCTIONS
You have purchased a quality industrial product that is
designed for high performance and long service life.
If correct use, safety and maintenance procedures
are observed this product will last for many years.
Thank you for choosing our
KOBE
Electric Fan. Your new fan has been designed using the latest technology.
With normal maintenance, your Electric Fan will provide years of satisfactory performance.
Please read this Owner's Manual carefully before using this fan and save it for future reference.
ASSEMBLING THE BASE, PILLAR, ADJUSTABLE POLE
AND MANUAL CONTROL PANEL
Step 1.
Align the pillar over the base, making sure that
the holes in the pillar align with the holes in the
base. Using the four screws, screw the pillar into
the base until secure.
Step 2.
Hold the adjustable pole and loosen the height
a d j u s t m e n t d i a l b y t w i s t i n g i t C O U N T E R -
CLOCKWISE, adjust the pole to the desired
height and tighten the height adjustment dial.
Step 3.
P l a c e t h e m a n u a l c o n t r o l p a n e l o n t o t h e
adjustable pole and tighten the adjustable pole
tightening clamp.
ASSEMBLY OF THE FAN GRILL AND BLADE
Step 1.
Remove the rear grill mounting nut. Place the
rear grill onto the motor housing, making sure
the handle on the rear grill is up.
Step 2.
Push the fan blade onto the motor shaft, lining
up the blade with the locating notch on the
motor shaft's end. Tighten the blade clamp by
turning it COUNTER-CLOCKWISE.
Step 3.
Hold the front grill of the fan, and using a
crosspoint screwdriver loosen the screw slightly
on the bottom of the grill ring, just enough to
relieve the tension. Angle the front grill and the
grill ring over the rear grill and snap into place.
Finally, tighten the screw on the grill ring.
Be sure your fan is in the OFF position.
Unplug the fan from the electricity supply.
Loosen the tightening grill ring and remove the front
grill.
Unscrew the blade clamp by turning it CLOCKWISE
(REVERSE THREAD).
Pull the fan blade away from the motor housing.
Gently wipe the fan blade and grill with a damp
cloth.
DO NOT immerse the fan in water and never allow
water to enter the motor housing.
DO NOT use gasoline, paint thinner or other
chemicals to clean the fan.
For storage, disassemble and clean the fan carefully
as instructed and store in its original box. You may
leave the fan assembled and covered to protect it
from dust. Store the fan in a cool dry place.
CAUTION: To avoid the risk of injury, always make sure that the front and rear
grill are locked together before operating.
When using electrical appliances, basic precautions
should always be followed to reduce the risk of fire,
electric shock and injury to persons, including the
following:
Always use this fan only as described in this
manual. Other uses not recommended may
cause fire, electric shock or injury to persons.
A l w a y s s u p e r v i s e a s n e c e s s a r y w h e n a n y
appliance is used by or near children.
Always avoid contact with moving fan parts.
Always turn the fan to the OFF position and
unplug the fan from the outlet when not in use
and before cleaning.
Always place the fan on a dry level surface.
Always check that the filters are clear and not
b l o c k e d . K e e p a l l o p e n i n g s c l e a r o f a n y
blockages.
Do not use this product outdoors.
Do not pull by the cord. To disconnect the fan,
first turn control to the OFF position, grip the
plug and pull it from the wall outlet.
Do not operate the fan in the presence of
explosive and/or flammable fumes.
Do not place the fan or any parts near an open
flame, cooking or other heating appliance.
Do not operate the fan with a damaged cord or plug
or if the product malfunctions, is dropped or
damaged in any manner.
Do not hang or mount fan on a wall or ceiling.
Do not operate if the fan housing is removed or
damaged.
Do not operate the fan without checking that the
protective front and rear grill are in position.
To protect against electric shock, do not
immerse unit, plug or cord in water or spray with
liquids.
Do not connect this fan to any power source
other than properly grounded ones. DO NOT
attempt to defeat this safety feature.This fan
requires a grounded power source.
The use of attachments is not recommended
and may be hazardous.
A loose fit between the AC outlet (receptacle)
and plug may cause overheating and a distortion
of the plug. Contact a qualified electrician to
replace loose or worn outlet.
If the Power cord is damaged, it must be
r e p l a c e d b y t h e q u a l i f i e d e l e c t r i c i a n o r
professional technician in order to avoid a
hazard.
Be sure your fan is in the off position.
Place the fan on a dry and level surface and plug
the cord into a grounded AC 240V 50Hz wall
outlet which should meet conditions in the
safety instruction.
Soft-touch adjustable tilting angle: tilt the fan
head slightly to desired angle.
Air flow setting: 0=Off, 1=low, 2=Medium,
3=High. 0=Power-Off, ON=Power-On
O s c i l l a t i o n : t o a c t i v a t e o r d i s e n g a g e t h e
oscillating feature, push down or pull up on the
oscillation button on the fan head.
1
Front Grill
2
Grill Ring
3
Blade Switch
4
Fan Blade
5
Rear Grill Mounting Nut
6
Rear Grill
7
Motor Housing
8
Oscillation Lever
9
Manual Control Panel
10
Decorated Cover
11
Speed Switch
GENERAL SAFETY
ASSEMBLY
SPECIFICATIONS
CLEANING AND STORAGE
OPERATION
19
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
12
Adjustable Pole
Tightening Dial
13
Power Cord
14
Adjustable Pole
15
Height Adjustment
Switch
16
Pillar
17
Base
18
Pad
19
Pillar Tightening Screw
Item
Components
Item
Components
Order Code
KBE-828-0010K
Model No.
KPF400
Power
60W (Max)
Adjustable Height
110 - 135mm
Blade Diameter
400mm (16”)
Weight
4Kg
Voltage
AC 240V 50Hz
Speed
3
Head Tilt
Adjustable
Oscillating Control
90
°
Fitted with plug in accordance with BS3456
