KOBE INDUSTRIAL AIR TOOLS
have been specifically designed to help you work
SAFELY
and
EFFICIENTLY
. Your care and good judgement are the best protection against injury, but always ensure
that the appropriate safety equipment is worn. All possible hazards cannot be covered here, but the most
important ones have been highlighted.
KOBE
INDUSTRIAL
AIR TOOLS
SAFETY INSTRUCTIONS
You have purchased a quality product that is designed for high performance
and long service life. If correct use, safety and maintenance procedures are
observed this machine will last for many years.
Always adhere to the processes and safety
warnings, which are stated in the instruction
manual.
GENERAL OPERATING HAZARDS
Always ensure all users are physically able and
competent to handle the size, weight and power
of the tools and have received appropriate
training to perform the task.
Always avoid accidental starting of the tool by
disconnecting it before replacing accessories or
repairing.
Always be aware of the tool rundown time.
Never allow routine to lead to mistakes.
Never operate if any parts are missing or
damaged.
Never allow untrained persons to operate the
tool.
WORKPLACE HAZARDS
Always ensure your working area is clean and
well lit.
When working at height make sure that the tool
is safely secured and be aware of objects falling
below. Make sure that no persons are working
directly below the working area.
Do not operate in explosive atmosphere, for
instance extreme dust, gases and liquids.
Keep children and bystanders away while
operating the tool. Distractions can cause you to
lose control.
Never run the tool in areas exposed to water or
in damp conditions.
PERSONAL PROTECTION
Always wear approved eye protection during
operation. Use safety glasses or goggles which
conform to BSEN136 or CE equivalent that
provide protection from the front and side. The
operator of the power tool is responsible for
following accepted eye, face, respiratory, hearing
and body protection.
Always ensure that all long hair and loose clothing,
ties, scarves, jewellery, etc., are secured or
removed.
Always consult a doctor if numbness, tingling,
pain or whitening of the skin occurs. Repetitive
work motions, awkward positions and exposure
to vibration can cause “Repetitive Strain
Injuries”.
When operating the tool stay alert and use
common sense, especially when it comes to
working at height. Be aware of what’s below you.
Do not overreach. Keep a proper balance and
footing at all times.
Do not use the tool if under the influence of
alcohol, drugs or medication.
SPECIFIC SAFETY INSTRUCTIONS
Always ensure all accessories are rated to the
“Free” speed of the air tool and intact before
fitting or using.
Always use air tool attachments that are in good
condition and are designed to be used with the
tool.
Always be aware of the risk of crushing between
the tool and the workpiece due to sudden
movement or reaction forces.
Always shut off air supply, drain hose of air
pressure and disconnect tools from air supply
when not in use, before changing accessories or
when making repairs.
Never apply additional or over excessive force to
the air tool.
2
KOBE
INDUSTRIAL
AIR TOOLS
PARTS BREAKDOWN
1
. . . KBE-298-5500A . . Housing
2
. . . KBE-298-9302S . . Spring pin (3x18L)
3
. . . KBE-298-5502C . . Connection
4
. . . KBE-298-5503D . . Throttle lever
5
. . . KBE-298-5504E . . Valve pin
6
. . . KBE-298-5505F . . Bushing
7
. . . KBE-298-5506G . . Throttle valve
8
. . . KBE-298-5507H . . Spring
9
. . . KBE-298-1978S . . “O” ring (22.8x2)
10
. . KBE-298-5509K . . Deflector
11
. . CES-298-0696P . . Ball bearing (696zz)
12
. . KBE-298-3762S . . Steel ball (2) (
3/32
”)
13
. . CES-298-0629D . . Ball bearing (627zz)
14
. . KBE-298-9314S . . Rear end plate
15
. . KBE-298-5514Q . . Rotor
16
. . KBE-298-5515R . . Vane (4)
17
. . KBE-298-5516S . . Idler gear pin (3) (4x15.8L)
18
. . KBE-298-5517T . . Cylinder
19
. . KBE-298-5518V . . Front end plate
20
. . KBE-298-5519W . . Nut
21
. . KBE-298-5609K . . Knob
22
. . KBE-298-5521Y . . Thread ring gear
23
. . KBE-298-5522Z . . Idler gear (3)
24
. . KBE-298-5524A . . Needle bearing (HK0910)
25
. . KBE-298-5525B . . Ratchet housing
26
. . KBE-298-5526C . . Crank shaft
27
. . KBE-298-5527D . . Idler gear plate
28
. . KBE-298-5528E . . Drive bushing
29
. . KBE-298-5529F . . Yoke
30
. . KBE-298-5530G . . Ratchet pawl
31
. . KBE-298-5531H . . Spring cap
32
. . KBE-298-5532J . . . Spring
33
. . KBE-298-5533K . . Washer
34
. . KBE-298-5534L . . Reverse button
35
. . KBE-298-5535M . . Pin (3.3x8.8)
36
. . KBE-298-9347S . . Spring pin (2x5L)
37
. . KBE-298-5537P . . Ratchet anvil
3/8
”
38
. . KBE-298-5538Q . . Spring (2)
39
. . KBE-298-3763S . . Steel ball (2) (
1/8
”)
40
. . KBE-298-5540S . . Thrust washer
41
. . KBE-298-5541T . . Retainer ring (IRTW-22)
42
. . KBE-298-00435 . . Spring pin (1.5x6L)
43
. . KBE-298-5543W . . Fixed shaft
44
. . KBE-298-5268X . . “O” ring (7.5x1.5)
45
. . KBE-298-5545Y . . Washer
46
. . KBE-298-5546Z . . “O” ring (2) (10.7x1.5)
47
. . KBE-298-5548A . . “O” ring (11.4x1.3)
48
. . KBE-298-0016S . . “O” ring (3.8x1.9)
49
. . KBE-298-5550C . . “O” ring (6.5x1.5)
50
. . KBE-298-2177S . . Spring pin (2.5x6L)
51
. . KBE-298-5552E . . Spring pin (2x12L)
52
. . KBE-298-5553F . . Damping material
53
. . KBE-298-5554G . . Ball bearing (689zz)
54
. . KBE-298-5555H . . Rubber grip
55
. . KBE-298-5556J . . . Rubber hat
56
. . KBE-298-5557K . . Specification label
57
. . KBE-298-9902A . . Warning label 29x16mm
58
. . KBE-298-9903A . . Warning label 20x16mm
No.
Order Code Description
No. Order Code Description