background image

kobalttools.com

25

•  Lay out the new saw chain in a loop and straighten 

any kinks. The cutters should face in the direction of 
chain rotation. If they face backwards, turn the loop 
over.

•  Place the chain drive links into the bar groove.

 Note: Make certain of direction of the chain.
•  Position the chain so there is a loop at the back of  

the bar.

•  Hold the chain in position on the bar and place the 

loop around the sprocket.

•  Fit the bar flush against the mounting surface so that 

the bar studs are in the long slot of the bar. Ensure 
that the chain is over the sprocket.

 Note: When placing the bar on the bar studs, ensure 

that the adjusting pin is in the chain tension pin hole.

•  Replace the chain cover.
•  Remove all slack from the chain by turning the chain 

adjustment screw (P) clockwise until the chain seats 
snugly against the bar with the drive links in the bar 
groove.

Bar Groove

Chain Drive Links

Cutters Chain Rotation

Chain Drive Links

CARE AND MAINTENANCE

•  Lift the tip of the guide bar up to check for sag.
•  Release the tip of the guide bar and turn the chain  

adjustment screw 1/2 turn clockwise. Repeat this  
process until sag does not exist.

•  Hold the tip of the guide bar up and tighten the chain 

cover lock nuts (K) by turning them with the wrench 
(O). The chain is correctly tensioned when there is 
no sag on the underside of the guide bar, the chain is 
snug, but it can be turned by hand without binding.

Содержание KCS 180B


































Отзывы: