Kobalt KCS 120-06 Скачать руководство пользователя страница 30

Страница: 30 / 31

kobalttools.com

TROUBLESHOOTING

PROBLEM

POSSIBLE CAUSE

CORRECTIVE ACTION

Bar and chain

running hot and

smoking.

1. Check chain tension for

overtightened condition.

2. Chain oil tank empty.

1. Tension chain. Refer to Chain

Tension earlier in this manual.

2. Check oil tank.

Motor runs, but

chain is not

rotating.

1. Chain tension too tight.

2. Check guide bar and chain

assembly.

3. Check guide bar and chain for

damage.

1. Re-tension chain. Refer to

Chain Tension earlier in this

manual.

2. Refer to Replacing the Bar and

Chain earlier in this manual.

3. Inspect guide bar and chain for

damage.

Motor runs, chain

rotates but does

not cut.

1. Dull chain.

2. Chain on backwards.

1. Sharpen chain.

2. Reverse direction of chain.

WARRANTY

5-YEAR HASSLE-FREE WARRANTY

This 40 V Lithiuim-Ion Cordless 12 in. Chain saw is warranted to the original purchaser from the

original purchase date for five (5) years subject to the warranty coverage described herein.

This 40 V Lithiuim-Ion Cordless 12 in. Chain saw is warranted for the original user to be free from

defects in material and workmanship.

If you believe that the 40 V Lithiuim-Ion Cordless 12 in. Chain saw is defective at any time during the

specified warranty period, simply return the 40 V Lithiuim-Ion chain saw along with proof of purchase

to the place of purchase for a free replacement or refund, or call 1-888-3KOBALT (1-888-356-2258)

for warranty service.

This warranty is void if: defects in materials or workmanship or damages result from repairs or

alterations which have been made or attempted by others or the unauthorized use of nonconforming

parts; the damage is due to normal wear, damage is due to abuse (including overloading of the tool

beyond capacity), improper maintenance, neglect or accident; or the damage is due to the use of the

tool after partial failure or use with improper accessories or unauthorized repair or alteration.

This warranty excludes bar and chain.

This warranty gives you specific legal rights, and you may also have other rights that vary from state

to state.

Содержание KCS 120-06
































Результаты поиска

Содержание KCS 120-06

Отзывы:

Похожие инструкции для KCS 120-06

Бренды по названию

Популярные бренды

Kobalt KCS 120-06, Руководство пользователя

Результаты поиска

Содержание KCS 120-06

Отзывы:

Похожие инструкции для KCS 120-06

Бренды по названию

Популярные бренды