background image

KDC User Manual                                                      A

PPLICATION 

G

ENERATION

 

 

12

 

Revision 1.0 

Copyright®2012-2015, KOAMTAC, Inc. 

 

2.

 

Installation   

 

2.1

 

Bluetooth Pairing   

The KDC500 can read and store barcode data independently, but it can also be used in 
combination with a PC, PDA, smartphone, or tablet. 

To use the KDC500 to read barcodes while it is paired with another device, the user should 
first set up a pairing between the KDC and smart device via Bluetooth. If no changes have 
been made in the smart device’s Bluetooth settings, the smart device will always recognize 
the KDC500 that has previously been paired. However, if changes have been made, the 
user will need to go through the pairing process again. The user can also refer to 

Chapter 

4. Bluetooth

 for more information about Bluetooth pairing.   

 

1. Put the KDC500 into 

Pairing

 mode   

 

 

Select and scan the correct pairing barcode below for your KDC model, or   

 

KDC500L/KDC500Li (1D)

 

 
 
 
 
 

KDC500C/KDC500Ci (2D) 

     
                                                                                                                                                                                   
 
 

      Pairing 

 

 

Select 

Pairing

 from the KDC500 menu, or 

From the KDC500 menu, select Normal, select BT Service, and select BT Pairing. 
 

 

Press the FN button for 5 seconds while the KDC500 is in the main screen. Then, 
select BT Pairing 

 

2. On the host device, go to 

Settings -> Bluetooth

, and select the KDC500 that needs to 

be paired. The KDC500 and host device will now communicate with each other.   

 

                                                                                                                                   

 

 

Содержание KDC 500

















Отзывы: