KNX KRISTAL BX-Q02B Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 16

KNX KRISTAL BX-Q02B Скачать руководство пользователя страница 13

After obtaining the desired brightness we will be able to release the button by
automatically causing the sending of the dimming STOP control.
Like in all previous cases, the

Contact type

property defined as Normally closed

will determine the reversal of the operation logic.
The effectiveness of the adjustment depends above all on the speed with which the

dimmer changes the brightness and is a parameter generally settable from the
actuator.

The Long control can operate in 3 different modes.
It  can  act  in  the  Brighter  mode  to  increase  the
brightness,  or  in  the  Darker  mode  to  decrease  the
brightness,  or  it  can  toggle  from  time  to  time

between these two modes to be able to fully control
the Dimmer with a single control.

Finally, we are describing here below the

Dimmer

Step

parameter.

This parameter determines by how much we can
increase or decrease the brightness with a single

Long press action.
100% means to be able to increase or decrease the
brightness throughout the required width.

50% means to be able to increase or decrease the
brightness up to half the required width. This means that in order to cover all of the
available range, we will have to perform two actions.
The possible variation with a single action can decrease up to 1%.

«
...
11
12
13
14
15
...
»

Содержание KRISTAL BX-Q02B

















Отзывы:

Нет отзывов