KNX Iddero Verso Скачать руководство пользователя страница 47

Страница: 47 / 103

Note

When using an external probe connected to one of the multifunction inputs as a tempera-
ture source, make sure to configure the input accordingly.

Parameter

Default page after home page

controls which page will be the first one shown imme-

diately after the Home page. This can be the Menu page, any of the configured control pages, or
the Favorites page.

3.3.2

Power saving mode

Parameter name

Values

Timeout for home page

0 ...

... 60 (x 1 min, 0 = Disabled)

Timeout for power saving mode

0 ...

... 60 (x 1 min, 0 = Disabled)

Page to show when leaving power saving
mode

Home page

/ Default page

Enable wake up object

[Checkbox]

This section controls the behaviour of the power saving mode (see

2.1.9 Power saving mode

page 20). The

Timeout for home page

and

Timeout for power saving mode

parameters define

the initial timeout values. Both of them can be adjusted from the user interface (Preferences >
Power saving).

Parameter

Page to show when leaving power saving mode

determines which page will be shown

when leaving power saving mode. This can be either the Home page or the “default” page

defined in the previous section.

A special

Wake up

communication object can optionally be enabled with the

Enable wake up

object

parameter. Writing the value “1” to this object wakes the device from power saving

mode.

3.3

User Interface

Содержание Iddero Verso








































































































Результаты поиска

Содержание Iddero Verso

Отзывы:

Похожие инструкции для Iddero Verso

Бренды по названию

Популярные бренды

KNX Iddero Verso, Руководство пользователя

Результаты поиска

Содержание Iddero Verso

Отзывы:

Похожие инструкции для Iddero Verso

Бренды по названию

Популярные бренды