background image

2

» Y276710 – (EN - REV. 001) | May 2020

Disclaimer

The information contained in this document is intended for the exclusive use of trained persons within the commercial vehicle industry, and must not be passed on 

to any third party. All recommendations regarding products and their servicing or usage are with reference to Knorr-Bremse products and should not be considered 

applicable to products from other manufacturers.
This information does not purport to be all-inclusive and no responsibility is assumed as a result of its use. We cannot accept any liability nor offer any guarantee 

regarding data accuracy, completeness or timeliness. The information does not represent any guarantee or ensured characteristics of the Products or Systems 

described. No liability can be accepted based on the information, its use, recommendations or advice provided. In no event may we be held liable for any damage 

or loss except in the case of wilful intent or gross negligence on our part, or if any mandatory legal provisions apply.
Any legal disputes arising from the use of this information shall be subject to German law.
Note: If service work is carried out on the vehicle, it is the responsibility of the workshop to ensure the vehicle is fully tested and in full functional order before the 

vehicle is returned into service. Knorr-Bremse accepts no liability for problems caused as a result of appropriate tests not being carried out.
This disclaimer is an English translation of a German text, which should be referred to for all legal purposes.

Revision Details

Rev. 000

June 2017

New document

Rev. 001

May 2020

Layout change

Содержание SKP

































Отзывы: