Knick SensoGate WA131MH Скачать руководство пользователя | Manualshive

Страница: 56 / 60

background image

SensoGate WA131MH

56

Glossary

CE Marking

Manufacturer's declaration, in accordance with EU Regulation 765/2008, that the product is in conformity with the appli-
cable requirements set out in the European Union harmonization legislation providing for its affixing.

Corrective Maintenance

Measures taken to return an item under review to an operational condition, with the exception of improvements.

Hazard

A hazard is defined as a potential source of damage. The term “hazard” can be specified to further describe the origin or
nature of the expected damage. (Source: EN ISO 12100)

Highly Efficient Charge Generating Mechanism

A highly efficient charge generating mechanism is [...] any charging mechanism stronger than manual rubbing of sur-
faces. (Source: EN ISO 80079-36)

Inspection

Measures for determining and assessing the actual condition of an item under review, including determining the causes
of wear and deriving the necessary steps for future use.

Maintenance

Combination of all technical, administrative and managerial actions during the life cycle of an item intended to retain it
in, or restore it to, a state in which it can perform the required function. (Source: EN 13306 Maintenance – Maintenance
terminology)

Preventive Maintenance

Measures for maintaining the target condition […] and delaying the reduction of the available wear margin of an item
under review.

Residual Risk

A residual risk is defined as the risk remaining after protective measures have been implemented. (Source: EN ISO 12100)

Risk

Combination of the probability of occurrence of harm and the severity of that harm (Source: EN ISO 12100)

Risk Assessment

Overall process of risk analysis and risk evaluation (Source: EN ISO 12100)

Zone 0

Area in which an explosive gas atmosphere is present continuously or for long periods or frequently.
(Source: IEC 60079-10-1)

«
...
54
55
56
57
58
...
»

Содержание SensoGate WA131MH





























































Отзывы:

Нет отзывов

Похожие инструкции для SensoGate WA131MH

Бренд: Salvis Страницы: 40

Бренд: IDEAL Страницы: 2

Бренд: GE Страницы: 14

Бренд: GE Страницы: 11

Бренд: GE Страницы: 20

Druck ADTS 2 Series

Бренд: GE Страницы: 18

Бренд: Keithley Страницы: 32

Бренд: jcb Страницы: 166

Бренд: Datavideo Страницы: 28

BODY ARMOR PRO TERM

Бренд: Darco Страницы: 6

Бренд: Raytheon Страницы: 68

Бренд: KegLand Страницы: 23

Бренд: Park House Healthcare Страницы: 12

Бренд: Zero 88 Страницы: 12

Бренд: Zeiss Страницы: 119

Бренд: Zehnder Rittling Страницы: 32

Бренд: Barreto Страницы: 16

Бренд: JBL Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды