Knick Protos II 4400 Скачать руководство пользователя

Страница: 62 / 112

Messages

Setting the Message Parameters

Messages

Note: Function check (HOLD) mode active

Menu Display

Messages

All parameters determined by the

measuring module can generate

messages.
• Device limits max:

Messages are generated when the

process variable (e.g. pH) is outside

the measuring range.

The “Failure” icon is displayed, the

NAMUR failure contact is activated

(BASE module, factory setting:

contact K4, N/C contact).

The current outputs can signal a

22 mA message (user defined).
• Variable limits:

For the “failure” and “warning” mes-

sages you can define upper and lower

limits for message generation.
• Message icons:

Messages (Administrator)

20.1 °C

Return

7.00 pH

Messages pH value (Administrator)

20.1 °C

Abort

Monitoring

7.00 pH

Variable limits

Device limits max.

Off

Messages Temperature

Messages ORP value

Messages pH value

Messages mV value

Messages rH value

Messages (Administrator)

20.1 °C

7.00 pH

Warning Limit Hi

Monitoring

Failure Limit Lo

Failure Limit Hi

Warning Limit Lo

+16.00 pH

Variable limits

+16.00 pH

–02.00 pH

Abort

Message list

22.3 °C

Fail pH range

Fail Meas. processing

7.00 pH

Fail Temperature range

Abort

Diagnostics menu

When the “Maintenance” or “Failure”

icons are flashing in the display, you

should call up the Diagnostics menu.

The messages are displayed in the

“Message list”.

Failure (Failure limit HiHi/LoLo)
Maintenance (Warning limit Hi/Lo)

he displa

y ma

y v

y depending on the devic

e v

ersion.

Содержание Protos II 4400

















































































































Результаты поиска

Содержание Protos II 4400

Отзывы:

Похожие инструкции для Protos II 4400

Бренды по названию

Популярные бренды

Knick Protos II 4400, Руководство пользователя

Результаты поиска

Содержание Protos II 4400

Отзывы:

Похожие инструкции для Protos II 4400

Бренды по названию

Популярные бренды