Knick Portavo 908 MULTI Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 76

background image

12

Start-Up

Inserting the Batteries

With four AA batteries, the Portavo has an
operating time of up to 500 h when oper-
ated in logger mode (see page 42).
Open the battery compartment on the
rear of the device. Be sure to observe the
correct polarity when inserting the batter-
ies (see markings in the battery chamber).
Close the battery compartment cover and
screw it handtight.

Check the shipment for transport damage and completeness (see Package
Contents).

NOTICE!
Do not operate the device when one of the following conditions applies:
•  the device shows visible damage
•  the device fails to perform the intended function
•  prolonged storage at temperatures above +70 °C / +158 °F
•  severe transport stresses
In this case, a professional routine test must be performed.
This test should be carried out at our factory.

A special lithium-ion battery (ZU 0925) suited to the battery compartment is avail-
able for the Portavo 908. Only this battery type can be charged directly from the USB
port.

A battery icon in the display indicates the battery power level:

Icon fully filled

Batteries at full capacity

Icon partially filled

Battery capacity is sufficient

Icon empty

Battery capacity not sufficient;
calibration is possible, no logging

Icon blinks

Only a few operating hours remaining,
measurement is still possible
NOTICE! It is absolutely necessary to replace
the batteries.

«
...
10
11
12
13
14
...
»

Содержание Portavo 908 MULTI













































































Отзывы:

Нет отзывов

Похожие инструкции для Portavo 908 MULTI

Бренд: Badger Meter Страницы: 47

Бренд: Hanna Instruments Страницы: 2

Бренд: Hanna Instruments Страницы: 2

Бренд: Hanna Instruments Страницы: 2

Бренд: Hanna Instruments Страницы: 4

Бренд: Hanna Instruments Страницы: 2

Бренд: K-Patents Страницы: 10

Бренд: Nady Audio Страницы: 2

Бренд: NARDA Страницы: 64

Бренд: OHAUS Страницы: 19

Бренд: OHAUS Страницы: 54

Бренд: Zenner Страницы: 2

Бренд: Sage Страницы: 68

FG-3000R Series

Бренд: Nidec Страницы: 8

Бренд: Victron energy Страницы: 46

Бренд: Sagola Страницы: 16

Бренд: KEM Страницы: 49

Бренд: Kinesys Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды