Knick Ceramat WA 154 Скачать руководство пользователя

Страница: 35 / 44

Accessories / Spare Parts

ZU 0647

Sensor mounting wrench, 19 mm

Required for safely screwing in the sensor

without overloading the PG 13.5 plastic

thread of the sensor head by an excessive

torque (as caused by an open-end wrench).

ZU 0648

Mounting wrench for Ceramat

Serves to disconnect the drive unit or

mount it to the process unit via the

coupling nut of the drive unit.

Sensor socket with mounted O-rings

•

ZU 0616

Sensor socket PEEK, O-rings FKM

•

ZU 0617

Sensor socket PEEK, O-rings EPDM

•

ZU 0618

Sensor socket PEEK, O-rings FFKM

•

ZU 0619

Sensor socket PEEK, O-rings EPDM FDA

•

ZU 0620

Sensor socket PVDF, O-rings FKM

•

ZU 0621

Sensor socket PVDF, O-rings EPDM

•

ZU 0622

Sensor socket PVDF, O-rings FFKM

•

ZU 0623

Sensor socket PVDF, O-rings EPDM FDA

Содержание Ceramat WA 154













































Результаты поиска

Содержание Ceramat WA 154

Отзывы:

Похожие инструкции для Ceramat WA 154

Бренды по названию

Популярные бренды

Knick Ceramat WA 154, Руководство пользователя

Результаты поиска

Содержание Ceramat WA 154

Отзывы:

Похожие инструкции для Ceramat WA 154

Бренды по названию

Популярные бренды