Knick A405B Скачать руководство пользователя | Manualshive

Страница: 63 / 108

background image

63

Selecting a Calibration Mode for 2-/4-Electrode Sensors

Note:
• All calibration procedures must be performed by trained personnel. Incorrectly

set parameters may go unnoticed, but change the measuring properties.

Calibration can be performed by:
• determining the cell constant (cell factor for toroidal sensors) with a known

calibration solution

•  entering the cell constant (cell factor for toroidal sensors)
•  sampling (product calibration)
•  zero calibration in air or with calibration solution (toroidal sensors)
•  temperature probe adjustment

Calibration adapts the device to the individual sensor characteristics.
Access to calibration can be protected with a passcode (SERVICE menu).
First, you open the calibration menu and select the calibration mode:

Calibration with calibration solution
Calibration by entry of cell constant
Product calibration (calibration with sampling)
Temperature probe adjustment

Calibration

Selecting a Calibration Mode for Toroidal Sensors

Calibration with calibration solution
Calibration by input of cell factor
Product calibration (calibration with sampling)
Zero calibration
Temperature probe adjustment

«
...
61
62
63
64
65
...
»

Содержание A405B













































































































Отзывы:

Нет отзывов

Похожие инструкции для A405B

Бренд: UEi Страницы: 20

Бренд: Hach Страницы: 138

Бренд: Datalogic Страницы: 6

Бренд: Datakom Страницы: 4

Бренд: Datakom Страницы: 38

Бренд: Zeversolar Страницы: 35

Бренд: Zenner Страницы: 52

Бренд: Magnescale Страницы: 64

SourceMeter 2430

Бренд: Keithley Страницы: 141

Бренд: Dräger Страницы: 538

Бренд: ETI Страницы: 2

Бренд: Neogen Страницы: 9

Бренд: Laser Technology Страницы: 80

Бренд: TE Connectivity Страницы: 3

Rangemaster CRF 1000

Бренд: Leica Страницы: 118

Бренд: SloanLED Страницы: 3

Proline Promag 50H

Бренд: Endress+Hauser Страницы: 52

Бренд: NetThings Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды